manualshive.com logo in svg

Hioki DM7275 Series, Instruction Manual

Share
Download
Hioki DM7275 Series Instruction Manual Download Page 178

179

Error Displays

Display

Description

Solution

INFO:081

Enter password for 

Adjustment Mode.

Enter the password for 

adjustment mode.

-

Err.Cal

Compensation values for 

self-calibration are not 

correct. There is a failure in 

communicating with the A/

D converter due to external 

noise or the instrument is 

malfunctioning.

If this error is displayed 

continuously, request for 

service.

Err.AD

A communication error with A/

D converter. There is a failure 

in communicating with the A/

D converter due to external 

noise or the instrument is 

malfunctioning.

If this error is displayed 

continuously, request for 

service.

Err.REF

Reference voltage error.

If this error is displayed 

continuously, request for 

service.

Maintenance and Service

14

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for DM7275 Series
















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands