manualshive.com logo in svg

Hioki DM7275 Series, Instruction Manual

Share
Download
Hioki DM7275 Series Instruction Manual Download Page 49

44

Starting Measurement

When comparator measurement or BIN measurement is set to ON

When comparator measurement (p. 53) or BIN measurement (p. 57) is set to 

ON

, the judgment 

results and sub-display are displayed automatically. 

You can display the Settings screen by touching 

SET

 on the sub-display.

Example: Displaying the Settings screen for comparator measurement

The screen display varies with the combination of comparator measurement and BIN measurement.

Comparator OFF, BIN OFF

Comparator ON, BIN OFF

Comparator OFF, BIN ON

NUMERIC

Normal

 display

BAR

 GRAPH

Bar

 graph

 display

BIN measurement judgment 

results are not shown.

TREND

Trend

 display

BIN measurement judgment 

results are not shown.

ST

ATISTICS

Statistics

 display

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for DM7275 Series
















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands