manualshive.com logo in svg

Hioki DM7275 Series, Instruction Manual

Share
Download
Hioki DM7275 Series Instruction Manual Download Page 21

15

Part Names and Functions

Rear

1

3

9

7

8

2

5

6

10

4

1 Power inlet

Connect the power cord 

(p. 25)

.

 See “Before connecting a power cord”(p. 8).

2

NPN/PNP switch

Switches the EXT I/O 

between NPN and PNP 

modes 

(p. 126)

.

Left: Current sink (NPN)
Right: Current source (PNP)

3

GP-IB connector

Used in GP-IB communications (p. 102)

.

Connect the instrument to a computer with a GP-IB cable.

4

RS-232C connector

Used in RS-232C communications 

(p. 100)

.

Connect the instrument to a computer, programmable controller, printer, or other 

device with an RS-232C cable. 

5

TEMP.SENSOR 

connector

Used to measure temperature 

(p. 27)

.

Connect the Z2001 Temperature Sensor.

6 EXT I/O connector

Used in external control (p. 125

).

Connect the input signal from a programmable controller, I/O board, or other 

device to control the instrument.

 See “Before connecting to the EXT I/O connector”(p. 12).

7

USB connector

Used in USB communications 

(p. 98)

.

Connect the instrument to a computer with a USB cable. 

8

Serial number

Do not remove the serial number as it is necessary for management purposes.

9

LAN connector

Used in LAN communications (p. 104)

.

Connect the instrument to a computer with a LAN cable.

10

Main power switch

Turns the instrument’s 

main power supply on and 

off 

(p. 28)

.

: Main power supply off
: Main power on

Model

Interfaces

DM7275

DM7276

LAN

USB

GP-IB

RS-232C

DM7275-01

DM7276-01

−

−

DM7275-02

DM7276-02

−

DM7275-03

DM7276-03

−

: Available, −: Not available

1

Overview

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for DM7275 Series
















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands