manualshive.com logo in svg

Hioki DM7275 Series, Instruction Manual

Share
Download
Hioki DM7275 Series Instruction Manual Download Page 67

64

Loading Measurement Conditions (Panel Load Function)

5.2  Loading Measurement Conditions (Panel Load 

Function)

The panel load function loads panel data that was previously saved in the instrument’s internal 

memory.

Panel data can be loaded as follows:

 • By means of touch panel operation

 • By sending communications commands from an external device

(See the Communication Command Instruction Manual on the included application disk.)

 • By sending signals from an external device

See “11 External Control (EXT I/O)” (p. 125), “8 Preparing to Use USB, RS-232C, GP-IB, 

and LAN Control” (p. 97)

This section describes how to load panel data using the touch panel. 

(Measurement screen) 

MENU

 > 

PANEL

1

 

Select the panel data to load. 

2

 

3

 

Touch 

OK

 to replace the current settings 

with the settings in the loaded panel data.

  

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for DM7275 Series
















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands