manualshive.com logo in svg

Hioki DM7275 Series, Instruction Manual

Share
Download
Hioki DM7275 Series Instruction Manual Download Page 163

163

Interface Specifications

13.4  Interface Specifications

LAN (standard 

equipment)

Standard compliance

IEEE 802.3

Transmission method

10BASE-T, 100BASE-TX (automatic detection)

Full-duplex transmission

Protocol

TCP/IP

Connector

RJ-45

Type of information 

sent and received

Settings and measurements via communications commands

Settings

IP address, subnet mask, default gateway

Communications command port: 1 to 9999

Default settings

IP address: 0.0.0.0

Subnet mask: 255.255.255.0

Default gateway: 0.0.0.0 (none)

Communications command port: 23

USB device (standard 

equipment)

(Not available when USB 

host is selected)

Electrical specifications USB 2.0 (full-speed)
Connector

Series B receptacle

Class

CDC class (USB COM), HID class (USB keyboard mode)

Default setting

CDC class (USB COM)

USB host (standard 

equipment)

(Not available when USB 

device is selected)

Class

Mass storage class (FAT16/32 support, no VFAT support)

Capacity limit

Up to 128 GB (theoretical value)

Saving of measured 

values

 •Touching the 

SAVE

 key outputs the current measured value 

or screen (BMP format).

 •All contents of measured value memory can be output to 

the USB flash drive from the File Operations screen.

File operations

Save settings (with or without panel information), load 

settings, delete, change name, display disk information

Settings

Output format: TEXT, SCREEN

Default settings

Default setting: TEXT

GP-IB (-02 model)

Standard compliance

IEEE 488.2

Interface actions

SH1, AH1, T6, L4, SR1, RL1, PP0, DC1, DT1, C0

Type of information 

sent and received

Settings and measurements via communications commands

Settings

Device address: 1 to 30

Delimiter: LF, CRLF

Default settings

Device address: 1

Delimiter: LF

13

Specifications

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for DM7275 Series
















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands