Hioki DM7275 Series Instruction Manual Download Page 31

Page: 31 / 207

Connecting the Measurement Cables (to the Instrument)

2.4

Connecting the Measurement Cables (to the

Instrument)

Before connecting the measurement cables, read “Before connecting a measurement cable”

(p. 9) carefully.

Connect the optional Hioki measurement cables to the instrument’s measurement terminals.

Use only Hioki measurement cables. See “Options (Sold Separately)” (p. 3) and “3.1

Connecting the Measurement Cables (Measurement Target)” (p. 31).

Protective cap

Each test lead plugs is covered by a protective cap.

Remove this cap before use.

Plug

Terminal

Red

HIGH

Black

LOW

Front

Voltage measurement terminals

Red

Black

Connect as follows:

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for DM7275 Series
















































































































































































































Search results

Summary of Contents for DM7275 Series

Reviews:

Brands by name

Popular brands

Hioki DM7275 Series, Instruction Manual

Search results

Summary of Contents for DM7275 Series

Reviews:

Brands by name

Popular brands