manualshive.com logo in svg

Hioki DM7275 Series, Instruction Manual

Share
Download
Hioki DM7275 Series Instruction Manual Download Page 100

98

Preparing to Use an Interface (Connection and Settings)

8.2 

Preparing to Use an Interface (Connection and 

Settings)

Using the USB interface

Preparation process

(1)  Set the instrument’s communications conditions.

(2)  Install the USB driver on the computer. (

p. 99

)

(When using the 

USB COM

 setting only)

(3)  Connect the USB cable. (

p. 99

)

Before connecting the instrument to the computer, you must install the USB driver on the 

included CD-ROM on the computer. Connecting the instrument to the computer before the driver 

has been installed will cause the standard USB driver that Microsoft ships with Windows to be 

automatically installed. The instrument cannot communicate properly with the standard Windows 

USB driver.

(1) Set the communications conditions. 

(Measurement screen) 

MENU

 > 

I/F

1

 

2

 

3

 

Select the transmission mode.

COM

(Rear panel)

(Default setting)

Select if connecting the 

instrument to the computer 

with a USB cable and 

communicating using a virtual 

COM port (when outputting 

data using a terminal emulator 

or a user-created program).

KEYBD

(Rear panel)

Select if connecting the 

instrument to the computer with 

a USB cable and outputting 

data (when outputting data as if 

it were typed using a keyboard 

into a text editor or spreadsheet 

software).

MEMORY

(Front panel)

Select if outputting data to a 

USB flash drive. (p. 115) 

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for DM7275 Series
















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands