manualshive.com logo in svg

Hioki DM7275 Series, Instruction Manual

Share
Download
Hioki DM7275 Series Instruction Manual Download Page 127

126

Switching between Current Sink (NPN) and Current Source (PNP)

11.2  Switching between 

Current Sink (

NPN) and 

Current Source (PNP)

Before using, read “Before switching the current sink (NPN) / current source (PNP)” (p. 11) 

carefully.

The NPN/PNP switch is used to change the type of programmable controller that can be supported. 

The instrument ships with the switch in the NPN position.

Left: Current sink (NPN)

Right: Current source (PNP)

See “Internal circuit architecture” (p. 133).

NPN/PNP switch setting

NPN

PNP

Input circuit

Supports programmable controllers 

that generate sink output.

Supports programmable controllers 

that generate source output.

Output circuit

Non-polar

Non-polar

ISO_5V power supply output

+5 V output

-5 V output

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for DM7275 Series
















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands