manualshive.com logo in svg

GE Sievers 500 RL, Operation And Maintenance Manual, Page: 156 / 186

Share
Download
GE Sievers 500 RL Operation And Maintenance Manual Download Page 156

GE Analytical Instruments ©2010

156 of 226

DLM 74001-04 Rev. A

Chapter 8: Troubleshooting

29 - USB Warning

Message: “A problem has been detected with the USB device. Please refer to the Oper. and Maint. manual for 
info on supported devices.”
Explanation: The Analyzer was unable to write to or read from the USB flash memory drive. Make sure the USB 
device is attached to the Analyzer properly and attempt the operation again. If you are not using the USB flash 
memory drive that was supplied in the Analyzer’s accessories kit, it is possible your USB device is not compatible 
with the Analyzer. For a list of known compatible USB flash memory drives, follow the Sievers 500 RL Analyzer 
link on our Web page, www.geinstruments.com.

32 - System Restore Error

Message: “Failed to restore system.”
Explanation: The attempt to restore the system settings failed. Make sure the USB drive that contains the saved 
system settings is attached to the Analyzer properly and try to restore again. If the error occurs again, try 
copying the files on the USB drive to a different USB drive, and then attempt to restore system settings again 
using the new USB drive. If the error message persists, contact GE Analytical Instruments technical support.

42 - ID Board Error

Message: “A problem has been detected with the ID Board. Please contact GE.”
Explanation: A communication error with the ID board has occurred. Turn the Analyzer off and on and restart 
analysis. If the warning persists, contact Technical Support.

43 - Analog Error (IC or TC Cell Conductivity)

Message: “Measurement out of range. Please refer to the Oper. and Maint. Manual for recommendations.”
Explanation: Ten (10) consecutive readings from the related channel are out of range. This warning generally 
displays when IC or TC cell conductivity is out of range. Confirm that there are no air bubbles in any tubing inside 
the Analyzer, and make sure the water level in the DI water cartridge is sufficient. Also confirm that sample 
water is flowing to the Analyzer. If necessary, turn the Analyzer off and on, and restart analysis. If the warning 
persists, contact Technical Support.

44 - Analog Error (Sample Cell Conductivity)

Message: “Measurement is out of range. Please refer to the Oper. and Maint. Manual for recommendations.”
Explanation: Ten (10) seconds from the related channel are out of range. This warning generally displays when 
sample cell conductivity is out of range. If starting the instrument after a prolonged amount of time, perform a 
rinse down. Confirm that there are no air bubbles in any tubing inside the Analyzer, and make sure the water 
level in the DI water cartridge is sufficient. Also confirm that sample water is flowing to the Analyzer. If 
necessary, turn the Analyzer off and on, and restart analysis. If the warning persists, contact Technical Support. 

45 - Analog Error (Temperature)

Message: “Measurement is out of range. Please refer to the Oper. and Maint. Manual for recommendations.”
Explanation: Ten (10) seconds of consecutive out-of-range readings have occurred on the sample cell 
conductivity channel. This warning generally displays when temperature is out of range. Confirm that there are 
no air bubbles in any tubing inside the Analyzer, and make sure the water level in the DI water cartridge is 
sufficient. Also confirm that sample water is flowing to the Analyzer. If necessary, turn the Analyzer off and on, 
and restart analysis. If the warning persists, contact Technical Support.

50 - Unstable Measurements Error

Message: “Unstable measurements detected during calibration/verification. Please refer to the Oper. and Maint. 
Manual for recommendations.”
Explanation: This error displays when the results from calibration/verification are inappropriate and calibration/
verification cannot continue. Follow the suggestions in the section called “Step 2: Visual Inspection” on page 159 

Summary of Contents for Sievers 500 RL



























































































































































































Reviews:

No comments