System Checks
GBC FusionPunch II Service Manual
12/2003
1-15
Table 1-4 Printer Control Panel Messages
Printer Message
Meaning
Operator Action
Technician Action
Docutech 61XX displays:
Jam in area 20 and external
finisher. (Fault Code P12-400)
Indicates that the printer has lost
communications with the external device.
Clear any jams, press Stop/Reset, resume the printer.
Check device profiles are correctly set.
Go to RAP 6.2 Printer
Connectivity.
Go to RAP 4.2 Punch Jam
Sensors and troubleshoot a
failure with the PUNCH EXIT
SENSOR.
Docutech 61XX displays:
External Finisher Jam. (Fault
Code P12-401)
Indicates that a fault has occurred in the
external device.
Clear any jams, press Stop/Reset, resume the printer.
Check device profiles are correctly set.
Ensure that there are no fault
indications at the downstream
device.
If no faults are present on the
downstream device, go to
RAP 5.5 Stacker Bypass Exit
Sensors
Docutech 61XX displays:
Jam in area 20 and external
finisher. (Fault Code P12-403)
Indicates that the external device did not
respond within the specified time to a sheet
that the IOT sent it.
Clear any jams, press Stop/Reset, resume the printer.
Check device profiles are correctly set.
Clear any jams, press Stop/
Reset, resume the printer.
Check device profiles are
correctly set.
If the failure continues to
occur, go to RAP 5.5 Stacker
Bypass Exit Sensors.
Docutech 135 displays:
Clear External Finisher to run
jobs to the Bypass Transport/
External Finisher Not Ready
The current job is faulted and requires a
reset.
The FusionPunch II is not on-line.
Click on the Printer Icon. Select reset if the reset option
is available.
Press Stop/Reset, then press Online/Offline to ensure
that the FusionPunch II is in online mode.
Go to RAP 6.2 Printer
Connectivity
Docutech 135, 61xx displays:
External Finisher Full
Xerox 4xxx Printer displays:
External Finisher Full
The Stacker is full and requires unloading.
Unload the Stacker. Start the FusionPunch II in online
mode.
Go to RAP 5.1 Stacker Full,
Stacker Almost Full and
Stacker Upper Switches.
Docutech 135, 61xx displays:
Clear External Finisher to run
jobs to the Bypass Transport or
External Finisher Not Ready
Xerox 4xxx Printer displays:
External Finisher Not Ready
The FusionPunch II is not in online mode.
Press Stop/Reset, then press Online/Offline to check
that the FusionPunch II is in online mode. Then, press
Start.
Go to RAP 6.2 Printer
Connectivity
Docutech 135, 61xx does not
recognize the Finisher.
Xerox 4xxx Printer does not
recognize the Finisher.
The Host Printer has no error message
displayed or has no External Finisher option.
Check that the Profile is loaded in the Printer and set
up correctly.
Contact your System Administrator to verify proper
Host Enablement.
Enable the Host Printer
Summary of Contents for FusionPunch II
