manualshive.com logo in svg

Fuji Xerox ApeosPort-V C2276, Administrator'S Manual

Share
Download
Fuji Xerox ApeosPort-V C2276 Administrator'S Manual Download Page 585

Error Code

585

Pro

b

lem

 So
lv

in

g

15

045-310
045-311
045-312
045-319
045-320
045-343
045-345
045-346
045-347
045-348
045-349
045-353
045-354
045-355
045-356
045-357
045-358
045-359
045-368
045-369
045-370
045-371
045-372
045-373
045-374
045-375
045-376
045-377
045-378
045-379

[Cause]

An error occurred.

[Remedy] Switch off the machine power, make sure that the touch screen is blank, and then switch 

on the machine power. If the same message is displayed again, contact our Customer 
Support Center.

047-211
047-212

[Cause]

An error occurred in the Offset Stacking Unit.

[Remedy] Switch off the machine power, make sure that the touch screen is blank, and then switch 

on the machine power. If the same message is displayed again, contact our Customer 
Support Center.

047-213

[Cause]

Detected the installation of a finisher of a different type than expected.

[Remedy] Switch off the machine power, make sure that the touch screen is blank, and then switch 

on the machine power. If the same message is displayed again, contact our Customer 
Support Center.

047-216

[Cause]

An error occurred while detecting the finisher.

[Remedy] Switch off the machine power, make sure that the touch screen is blank, and then switch 

on the machine power. If the same message is displayed again, contact our Customer 
Support Center.

047-217

[Cause]

An error occurred while detecting Tray 6 (HCF B1) (optional).

[Remedy] Switch off the machine power, make sure that the touch screen is blank, and then switch 

on the machine power. If the same message is displayed again, contact our Customer 
Support Center.

Error Code

Cause and Remedy

Summary of Contents for ApeosPort-V C2276
















































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands