manualshive.com logo in svg

Fuji Xerox ApeosPort-V C2276, Administrator'S Manual

Share
Download
Fuji Xerox ApeosPort-V C2276 Administrator'S Manual Download Page 557

Error Code

557

Pro

b

lem

 So
lv

in

g

15

024-340
024-341
024-342
024-343
024-345
024-346
024-347
024-348
024-349
024-350
024-351
024-352
024-353
024-354
024-355
024-356
024-357
024-358
024-359
024-360
024-361
024-362
024-363
024-364
024-365
024-366
024-367
024-368
024-370
024-371
024-372
024-373
024-375
024-376

[Cause]

An error occurred in the machine.

[Remedy] Switch off the machine power, make sure that the touch screen is blank, and then switch 

on the machine power. If the same message is displayed again, contact our Customer 
Support Center.

024-700

[Cause]

The memory capacity or hard disk required to use the optional feature is not installed.

[Remedy] Switch off the machine power, and then switch it on again after the touch screen goes 

out. If the error still is not resolved, contact our Customer Support Center.

024-701

[Cause]

The specified paper type is not compatible with the Face Up/Down Output setting 
selected.

[Remedy] Specify a paper type that is compatible with the Face Up/Down setting.

024-702

[Cause]

Paper jam occurred while [When Paper Jam Occurs] is set to [Delete Job] in [Print Service 
Settings].

[Remedy] Remove the jammed paper, and then try printing again.

024-704

[Cause]

An error occurred while receiving a print job from Denshi-Pen.

[Remedy] Switch off the machine power, make sure that the touch screen is blank, and then switch 

on the machine power. If the same message is displayed again, contact our Customer 
Support Center.

Error Code

Cause and Remedy

Summary of Contents for ApeosPort-V C2276
















































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands