Foma SO903iTV, Manual

Page: 380 / 390

23
Performing the Dial-up Connection
Connect the FOMA terminal to a PC before starting this
operation.
Example: When using Windows XP
1
Click [ スタート ] → [ すべてのプログラム ] → [ アク
セサリ
]
→
[
通信
]
→
[
ネットワーク接続
].
2
Double-click the host icon.
3
Check each item and click [
ダイヤル
].

You can connect with [
ユーザー名
] and [
パスワード
] left
blank when using “mopera U” or “mopera”.
The connection is established.
● The communication speed displayed on the PC may be
different from the actual communication speed.
● A n i c o n a p p e a r s o n t h e F O M A t e r m i n a l d u r i n g
communication.
During packet communication (no data transmission)
Ｃｏｎｎｅｃｔｉｎｇ
During packet communication (with data transmission)
Ｓｅｎｄｉｎｇ／ｒｅｃｅｉｖｉｎｇ
During 64K data communication
Ｃｏｎｎｅｃｔｉｎｇ ６４Ｋ ｄａｔａ
Disconnecting the Dial-up Connection
Sometimes, closing the Inter net browser does
n o t d i s c o n n e c t c o m m u n i c a t i o n . To e n s u re t h e
disconnection of communication, perform the following
procedure.
1
Click the dial-up icon in the task tray.
Dial-up icon
2
Click [ 切断 ].
The connection is disconnected.
AT Commands
AT commands are the commands (instructions) for
setting and changing the functions of the FOMA
terminal on a PC.
■ Input format of AT commands
Always enter an AT command by adding AT at the
beginning of the command. Be sure to use half-width
alphanumeric characters. An input example is given
below.
ATD ＊ 99 ＊＊＊ 3#

Return mark: Press Enter key. It separates the
commands.
Parameter: Description of the command
Command: Command name
Always enter an AT command including a parameter
(number and symbol) right after the command in one
line. One line means the row of characters from the first
character to the character immediately before pressing

.
■ Input mode of AT commands
To operate the FOMA terminal using AT commands, set
the PC to the terminal mode.
The terminal mode is used for operating a PC as a
communication terminal. The characters entered from
the keyboard are sent to the device connected to the
communication port or the line.
● Offline mode
The FOMA terminal is in stand-by status. This mode is
normally used when you operate the FOMA terminal using AT
commands.
● Online data mode
The FOMA terminal is in the status where communication is
in progress. If you enter an AT command in this status, the
characters sent are sent to the destination in their original
form and the modem at the destination may develop a
trouble. Do not enter AT commands during communication.
● Online command mode
This mode allows you to operate the FOMA terminal using AT
commands even if it is in the status where communication is
in progress. In this case, an AT command is executed while
the terminal remains connected to the destination. You can
continue communication again after completion of the AT
command execution.
Switching between the Online Data
Mode and Online Command Mode
You can use the following two methods to switch the
FOMA terminal between the online data mode and
online command mode.
 Enter the code set to “+++” command or “S2” register.

Set the ER signal of RS-232C( ※ ) to OFF when “AT&D1” is set.
※ Since the RS-232C signal line is emulated by a USB
interface, RS-232C signal line control by the communication
application is enabled.
To switch from the online command mode to the online
data mode, enter “ATO

”.