49
49
EN
ESIM384 Installation and Configuration Manual v1.1
Switch keypad par-
tition
Hold the [1]... [4] key and release it after 3 short beeps:
Value:
[1]... [4] key – partition number 1... 4 respectively.
Once the partition is switched and a valid user/master code is entered, indicator and the number [1]... [4] key, indicating the partition
that has been disarmed, will light OFF.
Disarm the system and
turn off the alarm
Enter user/master code:
uumm
Value:
uumm
– 4-digit user/master code.
Example:
2222
•
Partitioned system - disarming all 4 partitions simultaneously
– If a user/master code assigned to all 4 partitions exists, user can
disarm and turn OFF the alarm in all partitions simultaneously. When this feature is used, the system will proceed as follows:
•
if all partitions are armed and a valid user/master code is entered, indicator along with the number [1], [2], [3] and [4] keys will
light OFF.
•
if one or more partitions are disarmed unready (keypad number [1]... [4] key flashing, indicating the partition that contains violated
zone/tamper), the system will deny simultaneous partition disarming until the partition’s zone/tamper violation is removed.
•
if a combination of armed and disarmed ready partitions is present, the system will initiate exit delay. During the exit delay, the
keypad’s buzzer will emit short beeps and keypad indicator (if the keypad is switched to a disarmed partition) along with the
number [1]... [4] key, indicating the partition that is to be armed, will light ON. the disarmed-ready partitions will be armed and the
pre-armed ones will be skipped. In order to disarm all 4 partitions simultaneously, the user must repeat the following command:
Disarm and turn off
the alarm in all 4 parti-
tions simultaneously
Hold the [0] key, release it after 3 short beeps and enter user/ master code:
0 uumm
Value:
uumm
– 4-digit user/master code.
Example:
0 2222
Alternatively, the user can disarm and turn OFF the alarm in multiple partitions one by one (see
Partitioned system - disarming a single
partition
above).
notE:
If the user fails to enter a correct user/master code 10 times in a row, the system will block the keypad for 2 minutes. While the
keypad is blocked, the system prevents from entering any user/master code. the keypad will automatically unblock once the 2-minute
time has expired/
notE:
Before disarming all 4 partitions simultaneously, the user/master code must be assigned to all 4 partitions and the keypad
partition switch feature enabled (see
23.3. Keypad Partition and Keypad Partition Switch
).
12.5. EKB3W/EWKB4 Keypads and User/Master Code
attEntIon:
the user will be able arm/disarm only the first two system partitions using eKB3W keypad. Partition 3 and Partition 4 are
NOt supported by eKB3W keypad.
Illuminated indicator on eKB3W/eWKB4 keypad indicates that no violated zones and/or tampers are present, therefore the partition is
ready for arming. If the indicator is not illuminated, the partition is unready for arming, therefore the user must restore all violated zones
and/or tampers before arming the partition. Alternatively, the violated zones can be bypassed (see
14.7. Bypassing and activating
Zones
), disabled (see
14.9. Disabling and Enabling Zones
) or a Force attribute enabled (resulting in partial arm; see
14.6. Zone
attributes
), while the tampers can be disabled (see
16. taMPErS
). Indicator will illuminate or flash if system fault (-s) exist (see
29.
InDICatIon of SYStEM faUltS
).
the system will arm/disarm the partition corresponding to the one that user/master code and the keypad are assigned to. For example,
if User code 4 is assigned to Partition 2, while eKB3W/eWKB4 keypad is assigned to Partition 1, the user will be able to arm/disarm only
Partition 2 by entering User code 4. For more details on how to set keypad partition and user/master code partition, please refer to
23.3.
Keypad Partition and Keypad Partition Switch
and
23.4. User/ Master Code Partition
respectively.
12.5.1. arming the System
•
non-partitioned system
– When a valid user/master code is entered, the system will initiate exit delay, the keypad’s buzzer will emit
short beeps and the indicator will light ON. When the system is successfully armed, the keypad’s buzzer will silent down.
arm the system
Enter user/master code:
uumm
Value:
uumm
– 4-digit user/master code.
Example:
2222
