background image

How to use the manual

1 - How to use the manual

This manual has been prepared for Ducati Authorized Service Centers and workshop personnel 

involved in the maintenance and repair of Ducati motorcycles. It gives fundamental information on how 

to work in perfect harmony with the concepts of 

good technique

 and 

safety on work sites

 for 

servicing or replacing of original spare parts both for chassis and engine concerning this motorcycle. 

All operations described in this manual must be carried out by senior skilled technicians, who are 

requested to strictly follow the Manufacturer

s instructions.

Some information has been intentionally omitted, as, at our advice, a specialized technician must have 

this technical background. Additional information on how to install the different components is provided 

in the spare parts catalogue.

Caution

This manual also describes pre-delivery checks.

 

Ducati Motor Holding S.p.A. declines all responsibility for any technical errors or omissions in this 

manual and reserves the right to make changes without prior notice.

The information given in this manual was correct at the time of going to print. 

Caution

Reproduction and disclosure of all or part of the contents of this manual are strictly forbidden without 

prior written authorization of Ducati Motor Holding S.p.A. All rights on this manual are reserved for 

Ducati Motor Holding S.p.A. Applications for authorization must be submitted in writing and must 

specify the reasons for reproduction or disclosure.

 

 

Ducati Motor Holding S.p.A.

Manual layout

This manual is divided in sections (1), each identified by a letter.

Each section (1) includes several chapters (2), which are numbered consecutively. 

file:///C|/Documents%20and%20Settings/F4i/My%...0manual/wsm/usa/Mon695_MY07_A_1_3_00.3.1.html (1 of 2) [10/7/2008 8:41:32 PM]

Summary of Contents for MONSTER 695





















































































































































































































































































































































































































































































































































































































































Reviews: