dIXEL IPC400D SERIES User Manual Download Page 174

Page: 174 / 187

USER MANUAL – Release 1.2 of 01/01/2010

Page 174 of 191

Version: 02/03/2010

57.24

UNLOADING SIGNAL DUE TO LOW EVAPORATION PRESSURE IN HEATING

WORKING MODE

Display label meaning

b1Cu

(circuit n° 1 unloading from condenser coil signal)

b2Cu

(circuit n° 2 unloading from condenser coil signal)

b3Cu

(circuit n° 3 unloading from condenser coil signal)

b4Cu

(circuit n° 4 unloading from condenser coil signal)

Cause of activation

When working, if the probe configured as condensation temperature,
configured as pressure control or as evaporation pressure, measures a value <
Un13 set

Reset

if the condensation pressure/temperature or the evaporation pressure

measures a value > Un13 + Un14

With unloading function inserted after the time set Par. Un15

Reset

Automatic

Icon

flashing

Action

Alarm relay + buzzer NOT activated

Regulators

Alarm

Relay + buzzer NOT activated

Reverse valve

It follows its regulation

Recovery valve

it follows its regulation

Free-cooling on/off valve

it follows its regulation

Auxiliary relay

It follows its regulation

Idle running valve

It follows its regulation

Supply ventilation

It follows its regulation

Condensation ventilation

It follows its regulation

Support/boiler/anti-freeze

It follows its regulation

Pump/and water evaporator
and condenser

It follows its regulation

Compressors

It follows its regulation

Pump down solenoid valve It follows its regulation

Summary of Contents for IPC400D SERIES




























































































































































































Search results

Summary of Contents for IPC400D SERIES

Reviews:

Related manuals for IPC400D SERIES

Brands by name

Popular brands

dIXEL IPC400D SERIES, User Manual

Search results

Summary of Contents for IPC400D SERIES

Reviews:

Related manuals for IPC400D SERIES

Brands by name

Popular brands