dIXEL IPC400D SERIES User Manual Download Page 153

Page: 153 / 187

USER MANUAL – Release 1.2 of 01/01/2010

Page 153 of 191

Version: 02/03/2010

57. ALARMS

The alarm codes and signals are made up from letters and numbers that identify the different types.
Types of alarm:

•

Letter

= unit alarm

•

Letter

= circuit alarm

•

Letter

= compressor alarm

57.1

COMPRESSORS BLOCK ALARMS

If the compressors are OFF for:

•

Temperature control

•

Stand by

•

Remote OFF

AL30 = 0

the following alarms are ignored:

Thermal overolad compressors 1 to 16

AL15 = 0

the following alarms are ignored:

Oil low pressare / low level compressors 1 to 16

AL30

Compressor thermal overload alarm detection with compressor
OFF
0 = Disabled
1 = Enabled

AL15

Oil low pressure / low level alarm enabling with compressor OFF

Summary of Contents for IPC400D SERIES




























































































































































































Search results

Summary of Contents for IPC400D SERIES

Reviews:

Related manuals for IPC400D SERIES

Brands by name

Popular brands

dIXEL IPC400D SERIES, User Manual

Search results

Summary of Contents for IPC400D SERIES

Reviews:

Related manuals for IPC400D SERIES

Brands by name

Popular brands