dIXEL IPC400D SERIES User Manual Download Page 90

Page: 90 / 187

USER MANUAL – Release 1.2 of 01/01/2010

Page 90 of 191

Version: 02/03/2010

16.7.14 Screw compressor

This menu can be used to monitor the working status of the screw compressor in the various circuits.

The Set and Differential values can be modified.

By selecting the desired circuit and pressing

ENTER

, the following information can be displayed:

16.7.15 Control panel

Your own LCD keyboard can be customised in this menu.

The possible options in this menu are:

•

Contrast regulation

•

Back light time ON: regulation from 0 to 200 seconds, or always on

•

Language selection: Italian

English

Italian

•

Information regarding the system: Release software, setting IP address and MODBus node.

Summary of Contents for IPC400D SERIES




























































































































































































Search results

Summary of Contents for IPC400D SERIES

Reviews:

Related manuals for IPC400D SERIES

Brands by name

Popular brands

dIXEL IPC400D SERIES, User Manual

Search results

Summary of Contents for IPC400D SERIES

Reviews:

Related manuals for IPC400D SERIES

Brands by name

Popular brands