dIXEL IPC400D SERIES User Manual Download Page 169

Page: 169 / 187

USER MANUAL – Release 1.2 of 01/01/2010

Page 169 of 191

Version: 02/03/2010

57.18

DISCHARGE COMPRESSORS HIGH TEMPERATURE ALARM FROM

ANALOGUE INPUT

Display label meaning

C1dt

…

C16dt

(compressor n° 1…16 high discharge temperature alarm)

Cause of activation

The temperature measured by the probe configured as discharge high
temperature > AL50 set

Reset

The temperature measured by the probe configured as discharge high
temperature < AL50 set – AL51 differential

Reset

Automatic Manual. If more than AL52 interventions per hour occur. Enter the
functions menu to reset the alarm

Icon

flashing

Action

Alarm relay + buzzer activated

Regulators

Alarm

Relay + buzzer activated

Reverse valve

it follows its regulation

Recovery valve

it follows its regulation

Free-cooling on/off valve

it follows its regulation

Auxiliary relay

It follows its regulation

Idle running valve

It follows its regulation

Supply ventilation

It follows its regulation

Condensation ventilation

It follows its regulation

Support/boiler/anti-freeze

It follows/they follow its/their regulation

Pump/and water evaporator
and condenser

It follows its regulation

Compressor affected

Off

Compressor not affected

It follows its regulation

Pump down solenoid valve It switches-off if there is only 1 compressor per circuit, otherwise it follows its

regulation

Liquid injection solenoid
valve

Off with compressor in OFF

57.19

EVAPORATOR WATER INLET HIGH TEMPERATURE ALARM

Display label meaning

AEht

(evaporator water inlet high temperature alarm)

Cause of activation

During cooling mode, the temperature measured by the probe configured in
AL64 > AL62 set

Reset

The temperature measured by the probe configured in AL64 < AL62 set –
AL63 differential

Reset

Reset is always manual if AL60 = 0
Reset is always automatic if AL60 = 16
Reset passes from automatic to manual if AL60 goes from 1 to 15

Icon

flashing

Action

Alarm relay + buzzer activated

Regulators

Alarm

Relay + buzzer activated

Compressors

Off

Other loads

It follows its regulation

WARNING:

The alarm only appears if the unit is running with compressor on after time

AL61

Summary of Contents for IPC400D SERIES




























































































































































































Search results

Summary of Contents for IPC400D SERIES

Reviews:

Related manuals for IPC400D SERIES

Brands by name

Popular brands

dIXEL IPC400D SERIES, User Manual

Search results

Summary of Contents for IPC400D SERIES

Reviews:

Related manuals for IPC400D SERIES

Brands by name

Popular brands