dIXEL IPC400D SERIES User Manual Download Page 80

Page: 80 / 187

USER MANUAL – Release 1.2 of 01/01/2010

Page 80 of 191

Version: 02/03/2010

16.7 SERVICE KEY

By pressing the SERVICE key, enter the configuration of:

•

Parameters Programming

•

Time/Time periods Programming

•

Compressors

•

Water pump

•

Alarms display

•

Historical alarms

•

Defrost

•

Heaters/Liquid line solenoid valve

•

I/O status (Inputs and Outputs)

•

Thermostatic Valve

•

Heat recovery function

•

Auxiliary outputs

•

Free-cooling

•

Screw compressor

•

Control panel

16.7.1 Parameters programming

By selecting this menu it is possible to modify the value of the parameters depending on the Password level.
The parameters are divided per groups with the following meaning:

Label

Meaning

Displays temperature control parameters

Displays parameters to be viewed

Displays the basic configuration parameters of the unit

Displays the set-up parameters

Displays dynamic set-point parameters

Displays energy saving and automatic timed switch-on/off parameters

Displays compressor parameters

Displays evaporator condenser heating parameters

Displays pump down function parameters

Displays unloading function parameters

Displays ventilation parameters

Displays anti-freeze resistance parameters

Displays defrost parameters

Displays central compressor parameters

Displays recovery parameters

Displays the domestic hot water function parameters

Displays free-cooling function parameters

Displays auxiliary output parameters

Displays alarm parameters

Displays driver parameters for the management of the electronic thermostatic valve

Summary of Contents for IPC400D SERIES




























































































































































































Search results

Summary of Contents for IPC400D SERIES

Reviews:

Related manuals for IPC400D SERIES

Brands by name

Popular brands

dIXEL IPC400D SERIES, User Manual

Search results

Summary of Contents for IPC400D SERIES

Reviews:

Related manuals for IPC400D SERIES

Brands by name

Popular brands