dIXEL IPC400D SERIES User Manual Download Page 179

Page: 179 / 187

USER MANUAL – Release 1.2 of 01/01/2010

Page 179 of 191

Version: 02/03/2010

57.29

HEAT RECOVERY CONDENSER WATER PUMPING UNIT CIRCUIT BREAKER

ALARM

Display label meaning

AtC1

(condenser n°1 water pump circuit breaker)

AtC2

(condenser support n°2 water pump circuit breaker)

Cause of activation

ID configured as condenser n° 1 water pump circuit breaker active
ID configured as condenser n° 2 water pump circuit breaker active

Reset

With ID not active

Reset

Manual. (reset procedure in functions menu)

Icon

flashing

Action

Alarm relay + buzzer activated

Regulators

Alarm

Relay + buzzer activated

Reverse valve

It follows its regulation

Recovery valve

it follows its regulation

Free-cooling on/off valve

it follows its regulation

Auxiliary relay

it follows its regulation

Idle running valve

It follows its regulation

Supply ventilation

Off if no pump is available

Condensation ventilation

Off if no pump is available

Support/boiler/anti-freeze

It follows its regulation

Evaporator water pump

It follows its regulation

Condenser water pump

Off if no pump is available

Compressors

Off if no pump is available

Pump down solenoid valve

Off if no pump is available

57.30

UNIT N. 1 BLOCK GENERAL ALARM

Display label meaning

ALc1

Cause of activation

ID configured as unit n° 1 general block alarm active for the time set in the
Par. AL54

Reset

ID configured as unit general block alarm not active for the time set in the
Par. AL55

Reset

Automatic – becomes manual after AL53 interventions/hour (reset procedure
in functions menu) It is recorded in the historical alarms only with manual
reset

Icon

flashing

Action

Alarm relay + buzzer activated

Regulators

Alarm

Relay + buzzer activated

Other loads

Off

Summary of Contents for IPC400D SERIES




























































































































































































Search results

Summary of Contents for IPC400D SERIES

Reviews:

Related manuals for IPC400D SERIES

Brands by name

Popular brands

dIXEL IPC400D SERIES, User Manual

Search results

Summary of Contents for IPC400D SERIES

Reviews:

Related manuals for IPC400D SERIES

Brands by name

Popular brands