dIXEL IPC400D SERIES User Manual Download Page 175

Page: 175 / 187

USER MANUAL – Release 1.2 of 01/01/2010

Page 175 of 191

Version: 02/03/2010

57.25

UNLOADING SIGNAL DUE TO EVAPORATOR WATER INLET HIGH

TEMPERATURE

Display label meaning

AEun

(unloading signal from evaporator)

Cause of activation

In working mode if the evaporator water inlet temperature measured > Un1 set
for the time set in the Par. Un3

Reset

if the water temperature measured < Un1 set – Un2 differential

By unloading function inserted after the time set Par. Un4

Reset

Automatic

Icon

flashing

Action

Alarm relay + buzzer NOT activated

Regulators

Alarm

Relay + buzzer NOT activated

Reverse valve

It follows its regulation

Recovery valve

it follows its regulation

Free-cooling on/off valve

it follows its regulation

Auxiliary relay

It follows its regulation

Idle running valve

It follows its regulation

Supply ventilation

It follows its regulation

Condensation ventilation

It follows its regulation

Support/boiler/anti-freeze

It follows its regulation

Pump/and water evaporator
and condenser

It follows its regulation

Compressors

It follows its regulation

Pump down solenoid valve It follows its regulation

Summary of Contents for IPC400D SERIES




























































































































































































Search results

Summary of Contents for IPC400D SERIES

Reviews:

Related manuals for IPC400D SERIES

Brands by name

Popular brands

dIXEL IPC400D SERIES, User Manual

Search results

Summary of Contents for IPC400D SERIES

Reviews:

Related manuals for IPC400D SERIES

Brands by name

Popular brands