manualshive.com logo in svg

Dell C2660dn, User Manual

Share
Download
Dell C2660dn User Manual Download Page 61

Verifying the IP Settings 

You can confirm the settings by using the operator panel, printing the printer settings report, or using the ping 

command. 

Verifying the Settings Using Operator Panel 

1 

Press the 

(Menu)

 button. 

2 

Press the 

button until 

Admin Settings

 is highlighted, and then press the 

(Set)

 button. 

3 

Press the 

button until 

Network

 is highlighted, and then press the 

(Set)

 button. 

4 

Press the 

button until 

TCP/IP

 is highlighted, and then press the 

(Set)

 button. 

5 

Press the 

button until 

IPv4

 is highlighted, and then press the 

(Set)

 button. 

Check the IP address displayed on the operator panel. 

Verifying the Settings Using Printer Settings Report 

1 

Print the printer settings report. 
For details about how to print a printer settings report, see "Report / List." 

2 

Verify the correct IP address, subnet mask, and gateway address are listed in the printer settings report under 

Network (Wired)

 or 

Network (Wireless)

. 

If the IP address shows 

0.0.0.0

 (the factory default), an IP address has not been assigned. To assign one for your 

printer, see "Assigning an IP Address." 

Verifying the Settings Using Ping Command 

Ping the printer and verify that it responds. For example, at a command prompt on a network computer, type ping 

followed by the new IP address (for example, 192.168.0.11): 

ping 192.168.0.11 

If the printer is active on the network, you will receive a reply. 

Setting the IP Address 

59 

Summary of Contents for C2660dn










































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands