manualshive.com logo in svg

Dell C2660dn, User Manual

Share
Download
Dell C2660dn User Manual Download Page 338

Auger mark 

Action 

Yes 

No 

1 

Locate the cause of the problem using the Pitch Configuration Chart. 

a 

Launch the 

Tool Box

, and click 

Chart Print

 on the 

Diagnosis

 tab. 

b 

Click 

Pitch Configuration Chart

. 

Go to action 2. 

Contact Dell. 

The Pitch Configuration Chart is printed. 

Does the output match with the pattern for auger mark? 

2 

Replace the drum cartridges. See "Replacing the Drum Cartridges." 

The task is complete. 

Contact Dell. 

Does this solve your problem? 

Wrinkled/Stained paper 

Action 

Yes 

No 

1 

Verify that the correct print media is being used. See "Supported Paper  The task is complete. 

If printing on an 

Types." If not, use the print media recommended for the printer. 

envelope, go to action 

Does this solve your problem? 

2. 
If printing on print 

media other than 

envelopes, contact Dell. 

2 

Check the wrinkle. Is the wrinkle within 30 mm of the four edges of the 

This type of wrinkle is  Go to action 3. 

envelope? 

considered normal. 

Your printer is not at 

fault. 

3 

Load the envelopes in the MPF properly. For details, see "Loading an 

The task is complete. 

Contact Dell. 

Envelope in the MPF." 
Does this solve your problem? 

Troubleshooting Guide 

336 

Summary of Contents for C2660dn










































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands