manualshive.com logo in svg

DAS DL-300E, Installation Manual, Page: 9 / 57

Share
Download
DAS DL-300E Installation Manual Download Page 9

9

Location 000-003: Programming The Master Arm/Disarm Code

Locations 000-003 contain master arm/disarm code (user number 1). Location 000 contains the first digit of the code; location '003
contains the fourth digit of the code. THE CODE MUST CONTAIN FOUR (4) DIGITS. The master code can then be used in the RUN
mode to enter arm/disarm codes 1-30. The factory default code is [i][2][3][4].

Location 004-055: Programming The Arm/Disarm Code For Users 2 Thru 14

Locations 004-055 contain the arm/disarm codes for users 2 thru 14. To program these codes, follow the instructions in the
paragraph above. To disable these codes, program a "15" (factory default) as the first digit of the code. These codes can be
changed in the RUN mode using the master code (refer to operator's manual).

Location 056-059: 

Programming 

The Arm/Disarm Code For User 15 (Duress Code)

Locations 056-059 contain the arm/disarm code for user number 15 (Duress Code). To program this code, follow the instructions in
the paragraph above. This code can be used as a duress code if so programmed in locations 320-323. Factory default for this code is
"15", disabled.

Location 060-063: Programming The "Go To Program" Access Code

Locations 060-063 contain the "Go To Program" access code. Location 060 Contains the first digit of the code and location 063
contains the fourth digit of the code. THE CODE MUST CONTAIN FOUR (4) DIGITS. With the DL-300E disarmed, the "Go To
Program" access code can be used to enter the program mode. To disable the "Go To Program" access code, program a "15" in
location 060. The factory default setting is [9][7][1 ][3]. NOTE: The first digit of this code should not match the Quick-Arm digit.
NOTE: If a "15" is programmed into location 60 to disable this code, programming can only be accessed through the downloading
software or with a plug in programmer.

Location 064-079: Users 1-15 Arm/Disarm Code Enable By Partition

PARTITIONED SYSTEMS

If partitions are utilized, codes may be assigned to a specific partition by using locations 064-079. This is done by disabling each
individual code (code 1 is location 064, code 15 is location 079) for each of the four partitions that code should not have access to.
Codes are selected by adding the binary equivalents for each partition together and placing that number in the proper location.
Partition One = 1, Partition Two = 2, Partition Three = 4, and Partition Four = 8. For example, if code 2 should only be valid for
Partition Four, program a "8" in location 065. If code 10 is valid for Partitions Two, Three, and Four, a "14" would be programmed in
location 073. Factory default is "15", code valid for all partitions.

VALUE

PARTITION SELECTION

VALUE

PARTITION SELECTION

0

NO PARTITIONS ENABLED

8

ENABLES PARTITION 4

1

ENABLES PARTITION 1

9

ENABLES PARTITION 1 & 4

2

ENABLES PARTITION 2

10

ENABLES PARTITION 2 & 4

3

ENABLES PARTITION 1 & 2

11

ENABLES PARTITION 1, 2 & 4

4

ENABLES PARTITION 3

12

ENABLES PARTITION 3 & 4

5

ENABLES PARTITION 1 & 3

13

ENABLES PARTITION 1,3 & 4

6

ENABLES PARTITION 2 & 3

14

ENABLES PARTITION 2, 3 & 4

7

ENABLES PARTITION 1, 2 & 3

15

ENABLES PARTITION 1,2,3 & 4

Summary of Contents for DL-300E


























































Reviews:

No comments