manualshive.com logo in svg

DAS DL-300E, Installation Manual, Page: 51 / 57

Share
Download
DAS DL-300E Installation Manual Download Page 51

51

APPENDIX 1

This document lists the event reporting codes for Ademco Contact ID reporting in the DL-300E. The event codes are
programmed by placing a number from 0-15 in the "100's" location of the communicator code for the event being
reported. The 10 's and 1's digit rogrammed are sent as the Zone Identifier. The following event codes will be sent for
the digit programmed:

PROGRAMMED 100's DIGIT          ADEMCO

 EVENT CODE

DEFINITION

0

122

Silent panic

1

110

Fire

2

120

Panic

3

130

Burglary

4

131

Perimeter Burglary

5

132

Interior Burglary

6

133

24 Hour Auxiliary

7

134

Entry/Exit Burglary

8

135

Day/Night Burglary

9

150

Non-burg 24 Hour

10

121

Duress

11

100

Medical Alarm

12

123

Audible Panic

If the following numbers are programmed for the contact ID event code, the event code will be made up of 3 alternate
programming locations according to the following:

PROGRAMMED 100's DIGIT

PROGRAMMING LOCATIONS

13

365,366, 367

14

369, 370, 371

15

373, 374, 375

The following event codes are sent automatically but must be enabled by programming a 1 in the communicator code
location for that report:

REPORTING EVENT

           ADEMCO EVENT DIGIT

        LOCATIONS

Code pad Tamper

137

336

Autotest

602

340

Checksum Error

300

344

Opening/Closing

401

348 / 360

Cancel

406

354

A.C.Loss

301

356

Restore

Event code for alarm

364

Zone Bypass

570

368

Zone Trouble

380

372

Low Battery

302

260

Battery Test Fail

309

360 / 255

Late to Close

404

592

Early to Open

400

588

Download Complete

410

596

Summary of Contents for DL-300E


























































Reviews:

No comments