manualshive.com logo in svg

DAS DL-300E, Installation Manual, Page: 53 / 57

Share
Download
DAS DL-300E Installation Manual Download Page 53

53

APPENDIX 3

Certain older and unusual receivers have formats other than those listed on page 10. Locations 610 through 615 provide

various methods to duplicate these unusual formats. Included in these overrides is the ability to call and report to a

personal pager. The timer adjustment options allowed in locations 610 and 611 sometimes can compensate for

substandard, or older telephone exchanges. It is suggested that you call DAS technical assistance the first time you attempt

to use these override options.

Location 610

-

 

Inter-round time of a two round parity transmission. The inter-round time will be the nubmer contained

in location 610 times 800 mSec. If location 610 is "0", the time is determined by the individual formats in locations 101 and

123.

Location 611

- 

Inter digit time of a pulse format. If the number programmed in location 611 is something other than

the inter-digit time will be that number divided bythe PPS. For example, if the number in location 611 is "10", and the

format is a 20PPS format, the inter-digit time will be 10/20 of 0.5 secconds.

For locations 612 through 615, you must add the listed values for the desired characteristics and program

the sum in the appropriate location. If the value is not added for locations 612 and 613, the converse mode
will be enabled for those locations If the value of 1 is not added to location 612, the transmitted frequency
will be 1900 Hz. If the value of 2 is not added to location 613, the communicator will not transmit hex digits.
If neither of values 4 or 8 are added of location 613, the communicator will send messages at 40 PPS.

Location 612

-

VALUE

DESCRIPTION

The number programmed in this

1

Set for 1800 Hz pulse transmit frequency

location will determine the

selected

2

Set for 2300 Hz handshake frequency

default as desired.

4

Set for signal round checksum frequency

8

Set for 2 digit event code

Location 613

-

VALUE

DESCRIPTION

The number programmed in this

1

Set for extended reporting

location will determine the

selected

2

Set for hex digits

default as desired.

4

Set for 20 PPS

8

Set for 10 PPS

Location 614

-

VALUE

DESCRIPTION

The number programmed in this

1

Set for domestic dialing format

location will determine the

selected

2

Set for Ademco handshake

default as desired.

4

Reserved

8

Set for FBI Superfast

Location 615

-

VALUE

DESCRIPTION

The number programmed in this

1

Set for Contact ID and Ademco Highspeed

location will determine the

selected

2

Reserved

default as desired.

4

Set for 4/3 and Contact ID

8

Set for DTMF transmission format (4/2 Express, Superfast,

Ademco Highspeed & Contact ID)

Summary of Contents for DL-300E


























































Reviews:

No comments