manualshive.com logo in svg

DAS DL-300E, Installation Manual, Page: 30 / 57

Share
Download
DAS DL-300E Installation Manual Download Page 30

30

Location 364: Zone Restore Communicator Code

Location 332 is used to program the Restore code for zones (1 thru 32), when Contact I.D is selected. Note: Zone Restore
codes can only be reported if Zones are enabled to report Restores in the "Zone Report / Special Characteristics" locations

per individual zone. Default for Zone restore code is "0" enabled.

Location 365: Restore Code For Zones 9 Thru 16 (4+2 Only)

These locations should remain at factory default when Contact I.D is

selected

Location

 366: Restore Code For Zones 17 Thru 24 (4+2 Only)

These locations should remain at factory default when Contact I.D is

selected

Location

 367: Restore Code For Zones 25 Thru 32 4+2 Only)

These locations should remain at factory default when Contact I.D is

selected

Location 368: Zone Isolate Communicator Code

Location 334 is used to program reporting of the Isolate code for zones (1 thru 32), when Contact I.D is selected. Note:
Zone Isolate codes can only be reported if Zones are enabled to report Isolates in the "Zone Report / Special

Characteristics" locations per individual zone. When contact I.D is selected, program a one (1) in this location to enable
this report, an event "570 - Zone Isolate" will be reported. Default for Zone Isolate code is "0" enabled.

Location 369: Zone Isolate Code For Zones 9 Thru 16 (4+2 Only)

These locations should remain at factory default when Contact I.D is
selected

Location 370: Zone Isolate Code For Zones 17 Thru 24 (4+2 Only)

These locations should remain at factory default when Contact I.D is
selected.

Location 371: Zone Isolate Code For Zones 25 Thru 32 (4+2 Only)

These locations should remain at factory default when Contact I.D is

selected,

Location 372: Zone Trouble Communicator Code

Location 336 is used to program reporting of the Trouble code for zones (1 thru 32), when Contact I.D is selected. The

Trouble communicator code can be reported when a Trouble/24 Hour Tamper or Fire zone type is in sort circuit (Refer to
special communicator reporting characteristics or the zone type table ). When contact I.D is selected, program a one (1) in
this location to enable this report, an event "380 - Zone Trouble" will be reported..

Location 373: Zone Trouble Code For Zones 9 Thru 16 (4+2 Only)

These locations should remain at factory default when Contact I.D is
selected.

Summary of Contents for DL-300E


























































Reviews:

No comments