manualshive.com logo in svg

DAS DL-300E, Installation Manual, Page: 39 / 57

Share
Download
DAS DL-300E Installation Manual Download Page 39

39

THE FOLLOWING LOCATIONS ARE ACCESSIBLE ONLY THROUGH DOWNLOADING

Location 000-007: Control Panel Access Code

Locations 000-007 contain the eight digit access code the DL-300E must receive from the downloading software before the
panel will permit downloading to occur. The factory default code is listed in the instructions provided with the DAS
download 

software 

package.

Location 008-023: Cell Back Telephone Number

If a telephone number is programmed into these locations, and "callback" is enabled in location 024, the control panel will
hang tip for approximately 36 seconds (insuring that the calling patty has disconnected), and then call back. If tone dialing
is desired, program an "F" in the location where tone dialing should begin. If the entire number should be tone dialing,
program an "F" in location 008. Four second delays can be obtained anywhere in the sequence by programming a "D" in
the appropriate delay location. WARNING: THE CALLBACK PHONE NUMBER SHOULD ALWAYS BE REVIEWED FOR
ACCURACY BEFORE DISCONNECTING.

Location 024: Call Back Optional Features

The number programmed in location 660 will set the callback option for the control panel. Any or all of the features below
can be obtained by programming the appropriate data in this location. The correct data can be obtained by ADDING the
values of the corresponding characteristics from the table below (possible values are 0 to 7).

VALUE

CHARACTERISTIC

1

Panel will automatically callback for download

session.

2

Site initiated download call by entering [*][9][8][#]

at code
pad, and/or automatic callback if a "1" is

programmed in
location 822.

4

Panel will automatically callback when the event log

is full.

Example 1

- Programming a "5" (1 + 4= 5) in this location will combine the characteristics for values 1 and 4.

Example 2-

 Programming a "7" (1 +2 +4= 7) in this location will combine all of the characteristics described,

Location 025: Local Programming Lockout

Location 025 is used to disable local programming lockout. If a "5" is programmed in this location, all local programming is

hocked out. If an 'A" is programmed in this location, all programming functions related to the digital communicator will be
locked out. Any other number in location 025 will allow all local programming.

Location 026: Control Panel Shutdown

Location 026 is used to shut down the control panel. Programming an "A" in this location will completely shutdown the control

panel. The code pad will appear "dead", and the siren and communicator will not operate. WARNING: EXTREME CARE
SHOULD BE TAKEN NOT TO INADVERTENTLY PROGRAM THIS LOCATION.

Summary of Contents for DL-300E


























































Reviews:

No comments