DAS DL-300E Installation Manual Download Page 44

Page: 44 / 57

COMMUNICATOR CODES (CONTINUED)

LOCATION PAGE

DESCRIPTION

DATA

"DEFAULT"

209

AC POWER OUT Code pad SOUNDER ALERT

‘1’ ENABLED

210

SIREN/BELL TEST FEATURE

‘0’ DISABLED

211

Partial Mode SECURITY FEATURE (1 = FULL CODE TO DISARM)

‘0’ DISABLED

212

RINGBACK FEATURE

‘0’ DISABLED

213

MULTIPLE PARTITION : FIRST–TO-OPEN, LAST-TO-CLOSE

‘0’ DISABLED

214

RESETTABLE AUXILIARY POWER

‘1’ ENABLED

215

SIREN OUTPUT LIMIT (0 = UNLIMITED)

‘1’ LIMITED

216

COMMUNICATOR REPORT LIMIT(1 = LIMITED)

‘0’ UNLIMITED

217

PARTITION SIREN INHIBIT/CONTACT ID GROUP DIGIT REPORTING

‘0’ ALL PARTITION

218

RESERVED

‘1’ RESERVED

219

SWINGER SHUTDOWN FEATURE

‘0’ DISABLED

220

RESERVED

‘0’ RESERVED

221

DELAY OF PHONE LINE SEIZURE FOR ABORT (2 SECOND INCREMENTS)

‘0’ NO DELAY

222

QUICK ARM DIGIT (OPTION 1 TO 9)

‘0’ DISABLED

223

PARTIAL MODE DELAY TIME (10 SECOND

‘2’ 20 SECONDS

AUXILIARY OUTPUT OPTIONS

LOCATION PAGE

DESCRIPTION

DATA 1

DATA 2

DATA 3

DATA 4

"DEFAULT"

224-227

PIN #1

‘0-0-13-10’

228-231

PIN #2

‘0-0-13-11’

232-235

PIN #3

‘0-15-13-2’

236-239

PIN #4

‘0-0-13-2’

COMMUNICATOR CODES (CONTINUED)

LOCATION PAGE

DESCRIPTION

DATA

"DEFAULT"

240

INVERTING THE AUXILIARY OUTPUTS

‘0’

241

TIMIMG INCREMENTS FOR AUXILIARY OUTPUTS

‘0’

242

ANSWERING MACHINE DEFEAT (OPTIONS 1 TO 3 RINGS)

‘0’ DISABLED

243

NUMBER OF RINGS TO ANSWER DOWNLOAD CALL (INCREMENTS OF 2)

‘0’ DISABLED

244

ASSIGNING THE CHIME CODE OPTIONS 1 TO 9 ‘15’ = DISABLED

‘1’ ENABLED

245

ASSIGNING THE PARTIAL MODE CODE (OPTIONS 1 TO 9)

‘0’ DISABLED

246

COMMON AREA ENABLE (‘3’ = ENABLED)

‘0’ DISABLED

247

ZONES IN PARTITION # 1

‘0’ NONE

248

ZONES IN PARTITION # 2

‘0’ NONE

249

ZONES IN PARTITION # 3

‘0’ NONE

250

POWER UP CONDITION (‘1’ = DISARMED, ‘2’ = ARMED)

‘0’ PREVIOUS

251

POWER UP DELAY (10 SECOND INCREMENTS)

‘0’ NO DELAY

252

TELEPHONE LINE MONITOR

‘0’ DISABLED

253

TELEPHONE LINE MONITOR COUNTER

‘0’ DISABLED

254

DYNAMIC BATTERY TEST TIME (2 HOUR INCREMENTS)

‘3’ 6:00 AM

255

DYNAMIC BATTERY TEST DURATION (1 MINUTE INCREMENTS)

‘0’ DISABLED

Summary of Contents for DL-300E


























































Search results

Summary of Contents for DL-300E

Reviews:

DAS DL-300E, Installation Manual, Page: 44 / 57

Search results

Summary of Contents for DL-300E

Reviews: