Chrysler 300 SRT8 2010 User Manual Download Page 54 | Manualshive

Page: 54 / 449

background image

is mounted in the instrument panel, above the glove
compartment. The words SRS AIRBAG are embossed on
the airbag covers.

NOTE:

These airbags are certified to the new Federal

regulations for Advanced Airbags.

The Advanced Front Airbags have a multistage inflator
design. This allows the airbag to have different rates of
inflation based on the severity and type of collision.

This vehicle may also be equipped with Supplemental
Side Airbag Inflatable Curtains (SABIC) to protect the
driver, front, and rear passengers sitting next to a win-
dow. If the vehicle is equipped with SABIC airbags, they
are located above the side windows and their covers are
also labeled: SRS AIRBAG.

NOTE:

Airbag covers may not be obvious in the interior

trim; but they will open during airbag deployment.

Airbag System Components

The airbag system consists of the following:

•

Occupant Restraint Controller (ORC)

Front Airbag Components

1 — Airbags
2 — Knee Bolsters

54

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
52
53
54
55
56
...
»

Summary of Contents for 300 SRT8 2010


































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 SRT8 2010

Brand: Metra Electronics Pages: 14

Brand: Vauxhall Pages: 2

Brand: Uebler Pages: 18

Cherokee 16 1982

Brand: Jeep Pages: 1311

Multiple G9F18 AU000

Brand: Genesis Pages: 3

Brand: CITROEN Pages: 52

CB-796IG2-CIGD-R

Brand: CARRYBOY Pages: 4

Brand: GMC Pages: 428

Brand: Atera Pages: 10

4500 CHASSIS CAB 2012

Brand: RAM Pages: 7

Brand: T-Mobile Pages: 2

Brand: Streetwize Pages: 4

Brand: TomTom Pages: 22

Brand: TATA Motors Pages: 308

Brand: TracRac Pages: 8

Brand: MiX Telematics Pages: 39

Brand: Subaru Pages: 399

Brand: Hama Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands