Chrysler 300 SRT8 2010 User Manual Download Page 62 | Manualshive

Page: 62 / 449

background image

A quantity of non-toxic gas is generated to inflate the side
curtain airbag. The inflating side curtain airbag pushes
the outside edge of the headliner out of the way and
covers the window. The airbag inflates in about 30 ms
(about one-quarter of the time that it takes to blink your
eyes) with enough force to injure you if you are not belted
and seated properly, or if items are positioned in the area
where the side curtain airbag inflates. This especially
applies to children. The side curtain airbag is only about
3-1/2 in (9 cm) thick when it is inflated.

Because airbag sensors estimate deceleration over time,
vehicle speed and damage are not good indicators of
whether or not an airbag should have deployed.

NOTE:

In a rollover the pretensioners and/or SABIC

airbags may deploy on both sides of the vehicle.

Front and Side Impact Sensors

In front and side impacts, impact sensors aid the ORC in
determining appropriate response to impact events. Ad-
ditional sensors in the ORC determine the level of airbag
deployment and provide verification.

Enhanced Accident Response System

In the event of an impact causing airbag deployment, if
the communication network remains intact, and the
power remains intact, depending on the nature of the
event the ORC will determine whether to have the
Enhanced Accident Response System to perform the
following functions:

•

Cut off fuel to the engine.

•

Flash hazard lights as long as the battery has power or
until the ignition key is turned off.

62

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
60
61
62
63
64
...
»

Summary of Contents for 300 SRT8 2010


































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 SRT8 2010

Brand: kincrome Pages: 6

Brand: CITROËN Pages: 301

Brand: Draw tite Pages: 4

Brand: Mercedes-Benz Pages: 329

Brand: GMC Pages: 120

Brand: Prime Tech Pages: 6

inView 360 Fusion

Brand: Safe Fleet Pages: 27

ROADSIDE ASSISTANCE

Brand: Seat Pages: 44

2005 P207 Explorer Sport Trac

Brand: Ford Pages: 540

Brand: Skoda Pages: 281

2011 A3 Sportback

Brand: Audi Pages: 29

Brand: INDIWORK Pages: 18

Brand: Opel Pages: 103

Brand: Billien Pages: 2

Brand: Lexus Pages: 28

2008 Savana Van

Brand: GMC Pages: 402

Brand: Axxess Pages: 4

Brand: VP Autoparts Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands