manualshive.com logo in svg

Chrysler 300 SRT8 2010, User Manual

The 2010 Chrysler 300 SRT8 is a powerful and stylish sedan that demands attention on the road. To help you get the most out of this exceptional vehicle, we offer a detailed User Manual that you can easily download for free from our website. Explore its features and unleash the potential of your Chrysler 300 SRT8 today.

Share
Download
background image

Change Engine Oil

The oil change indicator system will remind you that it is
time to take your vehicle in for scheduled maintenance.
Refer to the “Maintenance Schedule” in Section 8 for
information on this system.

NOTE:

Under no circumstances should oil change

intervals exceed 6,000 miles (10 000 km) or six months,
whichever occurs first.

Engine Oil Selection

For best performance and maximum protection under all
types of operating conditions, the manufacturer only
recommends full synthetic engine oils that meet the
requirements of Chrysler Material Standard MS-10725
and are approved to MB 229.3 or MB 229.5 (will be listed
on the back label of the oil container).

CAUTION!

Do not use chemical flushes in your engine oil as the
chemicals can damage your engine. Such damage is
not covered by the New Vehicle Limited Warranty.

Engine Oil Viscosity (SAE Grade)

SAE 0W-40 or SAE 5W-40 engine oil is preferred for use
in all operating temperatures.

The engine oil filler cap also shows the recommended
engine oil viscosity for your engine. For information on
engine oil filler cap location, refer to “Engine Compart-
ment” in this section.

Synthetic Engine Oils

You may use synthetic engine oils provided the recom-
mended oil quality requirements are met, and the recom-
mended maintenance intervals for oil and filter changes
are followed.

7

MAINTAINING YOUR VEHICLE

359

Summary of Contents for 300 SRT8 2010


































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 SRT8 2010

Jeep Renegade Owner'S Handbook Manual preview
Renegade
Brand: Jeep Pages: 212
Wallbox Commander 2 Installation And User Manual preview
Commander 2
Brand: Wallbox Pages: 7
GMC ANDROID INTERFACE Instruction Manual preview
ANDROID INTERFACE
Brand: GMC Pages: 18
Prorack K496 Fitting Instructions For Basic Carrier preview
K496
Brand: Prorack Pages: 15
Yakima StickUp Installation Instructions Manual preview
StickUp
Brand: Yakima Pages: 21
Dodge 8W-30 Wiring Diagram preview
8W-30
Brand: Dodge Pages: 24
VDO DLD Wide Range II Installation Instructions Manual preview
DLD Wide Range II
Brand: VDO Pages: 84
Wagan TravelCharge Companion GO-Plus User Manual preview
TravelCharge Companion GO-Plus
Brand: Wagan Pages: 3
Camoplast Polaris TATOU 4S Installation Manuallines preview
Polaris TATOU 4S
Brand: Camoplast Pages: 13
VER-MAC PCMS Series Operation, Safety And Maintenance Manual preview
PCMS Series
Brand: VER-MAC Pages: 64
Fab Fours H4550 Installation Instructions Manual preview
H4550
Brand: Fab Fours Pages: 13
Skoda Superb 2006 Owner'S Manual preview
Superb 2006
Brand: Skoda Pages: 281
TOPPOINT LT95090 Quick Start Manual preview
LT95090
Brand: TOPPOINT Pages: 2
Edelbrock 5756 Installation Instructions preview
5756
Brand: Edelbrock Pages: 1
Front Runner LATF002 Quick Start Manual preview
LATF002
Brand: Front Runner Pages: 7
Nav TV MOST-HUR31 Manual preview
MOST-HUR31
Brand: Nav TV Pages: 8
Haltech NEXUS R3 Quick Start Manual preview
NEXUS R3
Brand: Haltech Pages: 13
Metra Electronics 99-6510 User Manual preview
99-6510
Brand: Metra Electronics Pages: 17

Brands by name

Popular brands

Load more brands