Chrysler 300 SRT8 2010 User Manual Download Page 31

Page: 31 / 449

2. Cycle the ignition switch between OFF and RUN and
then back to OFF four times ending up in the OFF
position (do not start engine).

3. Depress the power door LOCK switch to lock the
doors.

4. A single chime will indicate the completion of the
programming.

5. Cycle the ignition after performing steps one to four
for the feature to be enabled or disabled.

6. Repeat these steps if you want to return this feature to
its previous setting.

NOTE:

Use the Automatic Door Locks feature in accor-

dance with local laws.

Automatic Unlock Doors on Exit

The doors will unlock automatically on vehicles with
power door locks if:

1. The Automatic Unlock Doors On Exit feature is en-
abled.

2. The transmission was in gear and the vehicle speed
returned to 0 mph (0 km/h).

3. The transmission is in NEUTRAL or PARK.

4. The driver door is opened.

5. The doors were not previously unlocked, and

6. The vehicle speed is 0 mph (0 km/h).

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Summary of Contents for 300 SRT8 2010


































































































































































































































































































































































































































































Search results

Summary of Contents for 300 SRT8 2010

Reviews:

Related manuals for 300 SRT8 2010

Brands by name

Popular brands

Chrysler 300 SRT8 2010, User Manual

Search results

Summary of Contents for 300 SRT8 2010

Reviews:

Related manuals for 300 SRT8 2010

Brands by name

Popular brands