Chrysler 300 SRT8 2010 User Manual Download Page 339 | Manualshive

Page: 339 / 449

background image

(C) Injecting TIREFIT Sealant into the deflated tire:

•

Always start the engine before turning ON the TIRE-
FIT kit.

•

After pressing the Power Button (3), the sealant (white
fluid) will flow from the Sealant Bottle (1) through the
Sealant Hose (7) and into the tire.

NOTE:

Sealant may leak out through the puncture in

the tire.

If the sealant (white fluid) does not flow

within 0 –

10 seconds through the clear Sealant Hose (7):

1. Press the Power Button (3) to turn OFF the TIREFIT
kit. Disconnect the Clear Sealant Hose (7) from the valve
stem. Make sure the valve stem is free of debris. Recon-
nect the Clear Sealant Hose (7) to the valve stem. Check
that mode select knob (4) is on sealant mode position and
not air mode. Press the Power Button (3) to turn ON the
TIREFIT kit.

2. Connect the Power Plug (5) to a different 12 Volt
power outlet in your vehicle or another vehicle, if avail-
able. Make sure the engine is running before turning ON
the TIREFIT kit.

3. The Sealant Bottle (1) may be empty due to previous
use. Call for assistance.

NOTE:

If mode select knob (4) is on air mode and pump

is operating, air will dispense from black air pump hose
(6) only, not the clear sealant hose (7).

If the sealant (white fluid) does flow

through the clear

Sealant Hose (7):

1. Continue to operate pump until sealant is no longer
flowing through hose (typically takes 30 - 70 seconds). As
the sealant flows through hose (7), the pressure gauge (2)
can read as high as 70 psi (5 Bar). The pressure gauge (2)
will decrease quickly from approximately 70 psi to the
actual tire pressure when the sealant bottle is empty.

6

WHAT TO DO IN EMERGENCIES

339

«
...
337
338
339
340
341
...
»

Summary of Contents for 300 SRT8 2010


































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 SRT8 2010

Brand: Calira Pages: 14

Brand: Back View Pages: 168

Brand: Vaisala Pages: 24

Brand: Warrior Winches Pages: 17

Brand: Cequent Pages: 9

Brand: Whispbar Pages: 15

Brand: Thule Pages: 8

Brand: Jaeger Pages: 13

Brand: Motoalliance Pages: 5

Brand: PEUGEOT Pages: 17

Brand: Ferve Pages: 28

Brand: AutoLoc Pages: 6

Brand: Oldsmobile Pages: 358

Brand: Fabbri Pages: 32

Brand: Whelen Engineering Company Pages: 2

Charger SRT 392 2017

Brand: Dodge Pages: 576

Brand: Lexus Pages: 108

Brand: Lock'er Down Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands