Chrysler 300 SRT8 2010 User Manual Download Page 96 | Manualshive

Page: 96 / 449

background image

•

Only the phonebook of the currently connected cellu-
lar phone is accessible.

•

Only the cellular phone’s phonebook is downloaded.
SIM card phonebook is not part of the Mobile phone-
book.

•

This downloaded phonebook cannot be edited or
deleted on the uconnect™ phone. These can only be
edited on the cellular phone. The changes are trans-
ferred and updated to uconnect™ phone on the next
phone connection.

Phonebook Download — Single Entry

If equipped and supported by your phone, uconnect™
phone allows the user to download entries from their
phone via Bluetooth

威

. To use this feature, press the

button and say “Phonebook Download.” The system
prompts, “Ready to accept “V” card entry via
Bluetooth

威

…” The system is now ready to accept phone-

book entries from your phone using the Bluetooth

威

Object Exchange Profile (OBEX). Please see your phone
Owner’s Manual for specific instructions on how to send
these entries from your phone.

NOTE:

•

The phone handset must support Bluetooth

威

OBEX

transfers of phonebook entries to use this feature.

•

Some phones cannot send phonebook entries if they
are already connected to any system via Bluetooth

威

,

and you may see a message on the phone display that
the Bluetooth

威

link is busy. In this case, the user must

first disconnect or drop the Bluetooth

威

connection to

the uconnect™ phone, and then send the address book
entry via Bluetooth

威

. Please see your phone Owner’s

Manual for specific instructions on how to drop the
Bluetooth

威

connection.

•

If the phonebook entry is longer than 24 characters, it
will only use the first 24 characters.

96

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
94
95
96
97
98
...
»

Summary of Contents for 300 SRT8 2010


































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 SRT8 2010

Brand: Kargo Master Pages: 5

Brand: Camcar Pages: 6

Brand: OEM Tools Pages: 4

FRONT HEADLIGHT LENS COVER

Brand: Bimmer Jakes Pages: 4

Brand: TATA Motors Pages: 159

Brand: CALIMA Pages: 9

Brand: DriveRight Pages: 16

Brand: Jaeger Pages: 11

Brand: Skoda Pages: 2

Brand: ULTIMATE SPEED Pages: 26

Brand: Safe Fleet Pages: 28

Brand: Jaeger Pages: 13

Brand: Pet Gear Pages: 4

Brand: Ford Pages: 46

Brand: Jotto Desk Pages: 3

Brand: WALMEC Pages: 6

Brand: Yutrax Pages: 8

Brand: Ferrari Pages: 45

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands