manualshive.com logo in svg

Chrysler 300 SRT8 2010, User Manual

The 2010 Chrysler 300 SRT8 is a powerful and stylish sedan that demands attention on the road. To help you get the most out of this exceptional vehicle, we offer a detailed User Manual that you can easily download for free from our website. Explore its features and unleash the potential of your Chrysler 300 SRT8 today.

Share
Download
background image

Reprogramming A Single HomeLink

姞

Button

To reprogram a channel that has been previously trained,
follow these steps:

1. Place the ignition in the RUN position.

2. Press and hold the desired HomeLink

威

button for

20 seconds until the EVIC display states “CHANNEL #
TRAINING.”

Do not release the button.

3.

Without releasing the button,

proceed with Program-

ming HomeLink

威

Step 2 and follow all remaining steps.

Security

It is advised to erase all channels before you sell or turn
in your vehicle.

To do this, press and hold the two outside buttons for
20 seconds until the EVIC message states “CHANNELS
CLEARED.” Note that all channels will be erased. Indi-
vidual channels cannot be erased.

The HomeLink

威

Universal Transceiver is disabled when

the Vehicle Security Alarm is active.

Troubleshooting Tips

If you are having trouble programming HomeLink

威

, here

are some of the most common solutions:

•

Replace the battery in the original transmitter.

•

Press the LEARN button on the garage door opener to
complete the training for rolling code.

•

Did you unplug the device for training, and remember
to plug it back in?

If you are having any problems or require assistance,
please call toll-free 1–800–355–3515 or, on the Internet at
www.HomeLink.com for information or assistance.

164

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 300 SRT8 2010


































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 SRT8 2010

Dakota Digital VHX-37F Installation preview
VHX-37F
Brand: Dakota Digital Pages: 2
Dakota Digital BIM-01-2 Manual preview
BIM-01-2
Brand: Dakota Digital Pages: 7
Ecco EW4010 Installation And Operation Instructions Manual preview
EW4010
Brand: Ecco Pages: 9
Ecco EW4009 Installation And Operation Instructions Manual preview
EW4009
Brand: Ecco Pages: 9
TATA Motors Indigo Owner'S Manual & Service Book preview
Indigo
Brand: TATA Motors Pages: 164
Kathrein DDA Series User Manual preview
DDA Series
Brand: Kathrein Pages: 7
Wagan 2227-1 User Manual preview
2227-1
Brand: Wagan Pages: 8
Thermo King T- series Driver Manual To Simple Operation preview
T- series
Brand: Thermo King Pages: 2
Volkswagen 1973 Convertible Owner'S Manual preview
1973 Convertible
Brand: Volkswagen Pages: 80
Waeco MagicComfort MSH200 Installation And Operating Instructions Manual preview
MagicComfort MSH200
Brand: Waeco Pages: 108
Tusk RL-HM018R Installation Instructions And Information Manual preview
RL-HM018R
Brand: Tusk Pages: 2
Gatorback Mudflaps GCR53F Mounting Diagram & Instructions preview
GCR53F
Brand: Gatorback Mudflaps Pages: 4
Chevrolet Malibu 2014 Owner'S Manual preview
Malibu 2014
Brand: Chevrolet Pages: 428
WABCO Truck Training Model Operating Instructions Manual preview
Truck Training Model
Brand: WABCO Pages: 56
VER-MAC PCMS Series Operation, Safety And Maintenance Manual preview
PCMS Series
Brand: VER-MAC Pages: 64
Cadillac 2003 Seville Owner'S Manual preview
2003 Seville
Brand: Cadillac Pages: 402
Cobra BAK R294 Manual preview
BAK R294
Brand: Cobra Pages: 2
Sagem MyCK100 User Manual preview
MyCK100
Brand: Sagem Pages: 10

Brands by name

Popular brands

Load more brands