Chrysler 300 SRT8 2010 User Manual Download Page 192 | Manualshive

Page: 192 / 449

background image

WARNING!

A malfunctioning catalytic converter, as referenced
above, can reach higher temperatures than in normal
operating conditions. This can cause a fire if you
drive slowly or park over flammable substances such
as dry plants or wood or cardboard, etc. This could
result in death or serious injury to the driver, occu-
pants or others.

25. Oil Pressure Warning Light

This light indicates low engine oil pressure. The
light should turn on momentarily when the engine

is started. If the light turns on while driving, stop the
vehicle, and shut OFF the engine as soon as possible. A
single chime will sound when this light turns on.

Do not operate the vehicle until the cause is corrected.
This light does not indicate how much oil is in the engine.
The engine oil level must be checked using the procedure
shown in Section 7.

ELECTRONIC VEHICLE INFORMATION CENTER
(EVIC)

The Electronic Vehicle Information Center (EVIC) fea-
tures a driver-interactive display that is located in the
instrument cluster.

Electronic Vehicle Information Center (EVIC)

192

UNDERSTANDING YOUR INSTRUMENT PANEL

«
...
190
191
192
193
194
...
»

Summary of Contents for 300 SRT8 2010


































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 SRT8 2010

Brand: Yakima Pages: 12

Brand: JEHNERT SOUND DESIGN Pages: 8

Experience Series

Brand: Rainbow Pages: 19

Brand: Yakima Pages: 12

Brand: FABBRI PORTATUTTO Pages: 2

Brand: IAG Pages: 3

iBoard IB-ZK406

Brand: APS Auto Parts Specialist Pages: 3

Brand: FormFit Pages: 4

WrapAround Windjammer

Brand: Bestop Pages: 7

Dodge Charger TufBox

Brand: TUFLOC Pages: 6

Lippert Components LEVELEGS MPD 66385

Brand: Atwood Pages: 6

65 41 2 152 528

Brand: BMW Pages: 21

Brand: Yakima Pages: 13

Brand: Menabo Pages: 11

Brand: Subaru Pages: 21

Brand: Whispbar Pages: 15

Brand: mtf TRANSPORT SYSTEM Pages: 9

Brand: Warn Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands