Chrysler 300 SRT8 2010 User Manual Download Page 154 | Manualshive

Page: 154 / 449

background image

ParkSense

威

uses four sensors located in the rear bumper

to scan for obstacles up to 79 in (200 cm) away from the
rear bumper fascia. The ParkSense

威

Warning Display

located above the rear window provides both visible and
audible warnings to indicate the range of the object.

The Warning Display contains two sets of yellow and red
indicators, one set to warn of obstacles behind the left
rear of the vehicle and the other set to warn of obstacles
behind the right rear of the vehicle. The driver can view
the indicators either through the rearview mirror or by
looking at the display above the rear window.

ParkSense

威

dimly illuminates the two inner most yellow

indicators when it is ON and detecting no obstacles. The
following chart shows the warning display operation
when the system is detecting an obstacle:

ParkSense

威

LED Display

154

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
152
153
154
155
156
...
»

Summary of Contents for 300 SRT8 2010


































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 SRT8 2010

Brand: Garmin Pages: 2

Brand: Vauxhall Pages: 323

Brand: Daewoo Pages: 68

Brand: Hyundai Pages: 437

Brand: Fiat Pages: 172

Brand: Honda Pages: 6

Brand: Uebler Pages: 56

Brand: hc-cargo Pages: 60

Brand: Whispbar Pages: 15

Brand: Opel Pages: 254

Brand: GMC Pages: 120

Brand: Prime Tech Pages: 6

Brand: Acura Pages: 6

Brand: FALCON RIDGE Pages: 4

Brand: Airstream Pages: 103

Brand: HAKR Pages: 10

Brand: Yakima Pages: 8

Brand: Volvo Pages: 275

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands