manualshive.com logo in svg

Chrysler 300 SRT8 2010, User Manual

The 2010 Chrysler 300 SRT8 is a powerful and stylish sedan that demands attention on the road. To help you get the most out of this exceptional vehicle, we offer a detailed User Manual that you can easily download for free from our website. Explore its features and unleash the potential of your Chrysler 300 SRT8 today.

Share
Download
background image

Adding Coolant

Your vehicle has been built with an improved engine
coolant (antifreeze) coolant that allows extended mainte-
nance intervals. This engine coolant (antifreeze) can be
used up to five years or 102,000 miles (170 000 km) before
replacement. To prevent reducing this extended mainte-
nance period, it is important that you use the same
engine coolant (antifreeze) throughout the life of your
vehicle. Please review these recommendations for using
Hybrid Organic Additive Technology (HOAT) engine
coolant (antifreeze).

When adding engine coolant (antifreeze):

•

The manufacturer recommends using MOPAR

威

Antifreeze/Coolant 5 Year/100,000 Mile Formula
HOAT (Hybrid Organic Additive Technology) or
equivalent.

•

Mix a minimum solution of 50% HOAT engine coolant
(antifreeze) and distilled water. Use higher concentra-
tions (not to exceed 70%) if temperatures below

⫺

34°F

(

⫺

37°C) are anticipated.

•

Use only high purity water such as distilled or deion-
ized water when mixing the water/engine coolant
(antifreeze) solution. The use of lower quality water
will reduce the amount of corrosion protection in the
engine cooling system.

Please note that it is the owner’s responsibility to main-
tain the proper level of protection against freezing ac-
cording to the temperatures occurring in the area where
the vehicle is operated.

NOTE:

Mixing engine coolant (antifreeze) types will

decrease the life of the engine coolant (antifreeze) and
will require more frequent engine coolant (antifreeze)
changes.

7

MAINTAINING YOUR VEHICLE

371

Summary of Contents for 300 SRT8 2010


































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 SRT8 2010

B-Speech B-Speech Prim Manual preview
B-Speech Prim
Brand: B-Speech Pages: 18
Camoplast T4S User Manual preview
T4S
Brand: Camoplast Pages: 60
LAS BC260 Operating Instructions Manual preview
BC260
Brand: LAS Pages: 44
LAS 11807 Operating Instructions Manual preview
11807
Brand: LAS Pages: 24
CITROEN PICASSO XSARA DESIRE 1.6 - MESUREMENT Manual preview
PICASSO XSARA DESIRE 1.6 - MESUREMENT
Brand: CITROEN Pages: 2
Alpine eX-10 Owner'S Manual preview
eX-10
Brand: Alpine Pages: 69
Allen Sports S302 Instructions preview
S302
Brand: Allen Sports Pages: 2
BGS technic 40108 Manual preview
40108
Brand: BGS technic Pages: 5
Oldsmobile 1999 88 Owner'S Manual preview
1999 88
Brand: Oldsmobile Pages: 344
ABL eMH3 Installation Manual preview
eMH3
Brand: ABL Pages: 66
SnapPad EQ Round Installation Instructions preview
EQ Round
Brand: SnapPad Pages: 5
WABCO TP19108 Installation Manual preview
TP19108
Brand: WABCO Pages: 32
ideus VV950 User Manual preview
VV950
Brand: ideus Pages: 159
Calitop Calispace Ocean 80 Assembly Instructions preview
Calispace Ocean 80
Brand: Calitop Pages: 5
walser ULTIMATE SPEED 296713 Assembly And Safety Advice preview
ULTIMATE SPEED 296713
Brand: walser Pages: 10
Mercedes-Benz 2009 E-Class Manual preview
2009 E-Class
Brand: Mercedes-Benz Pages: 373
Prorack K349 Fitting Instructions Manual preview
K349
Brand: Prorack Pages: 13
Gigaware Gigaware 12-493 User Manual preview
Gigaware 12-493
Brand: Gigaware Pages: 8

Brands by name

Popular brands

Load more brands