manualshive.com logo in svg

Chrysler 300 SRT8 2010, User Manual

The 2010 Chrysler 300 SRT8 is a powerful and stylish sedan that demands attention on the road. To help you get the most out of this exceptional vehicle, we offer a detailed User Manual that you can easily download for free from our website. Explore its features and unleash the potential of your Chrysler 300 SRT8 today.

Share
Download
background image

Air Conditioner Maintenance

For best possible performance, your air conditioner
should be checked and serviced by an authorized dealer
at the start of each warm season. This service should
include cleaning of the condenser fins and a performance
test. Drive belt tension should also be checked at this
time.

CAUTION!

Do not use chemical flushes in your air conditioning
system as the chemicals can damage your air condi-
tioning components. Such damage is not covered by
the New Vehicle Limited Warranty.

WARNING!

•

Use only refrigerants and compressor lubricants
approved by the manufacturer for your air condi-
tioning system. Some unapproved refrigerants are
flammable and can explode, injuring you. Other
unapproved refrigerants or lubricants can cause
the system to fail, requiring costly repairs. Refer to
Section 3 of the Warranty Information book, lo-
cated on the DVD, for further warranty informa-
tion.

•

The air conditioning system contains refrigerant
under high pressure. To avoid risk of personal
injury or damage to the system, adding refrigerant
or any repair requiring lines to be disconnected
should be done by an experienced technician.

7

MAINTAINING YOUR VEHICLE

363

Summary of Contents for 300 SRT8 2010


































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 SRT8 2010

Calira 811 Manual preview
811
Brand: Calira Pages: 14
Camcar 40104 Mounting Instructions preview
40104
Brand: Camcar Pages: 6
Dakota Digital VHX-37F Installation preview
VHX-37F
Brand: Dakota Digital Pages: 2
Dakota Digital BIM-01-2 Manual preview
BIM-01-2
Brand: Dakota Digital Pages: 7
Subaru 2005 Baja Owner'S Manual preview
2005 Baja
Brand: Subaru Pages: 34
Whispbar K611W Fitting Instructions Manual preview
K611W
Brand: Whispbar Pages: 77
CITROËN C4 CACTUS Handbook preview
C4 CACTUS
Brand: CITROËN Pages: 301
Thule Kit 2161 Fitting Instructions preview
Kit 2161
Brand: Thule Pages: 2
Würth 071554055 User Instructions preview
071554055
Brand: Würth Pages: 36
TATA Motors 2013 Nano Owner'S Manual preview
2013 Nano
Brand: TATA Motors Pages: 136
Harman Kardon DP 2US Quick Start Manual preview
DP 2US
Brand: Harman Kardon Pages: 16
TATA Motors TIAGO XZ 2019 Owner'S Manual preview
TIAGO XZ 2019
Brand: TATA Motors Pages: 184
B&G electronics PW-50C Civilian Installation And Operation Manual preview
PW-50C Civilian
Brand: B&G electronics Pages: 7
Fab Fours F2950 Installation Instructions Manual preview
F2950
Brand: Fab Fours Pages: 21
Tellur BASIC TLL171231 User Manual preview
BASIC TLL171231
Brand: Tellur Pages: 5
Mercedes-Benz 240 D 1979 Owner'S Manual preview
240 D 1979
Brand: Mercedes-Benz Pages: 91
Honda 1991 Civic Online Reference Owner'S Manual preview
1991 Civic
Brand: Honda Pages: 124
Thule Kit 1312 Instructions Manual preview
Kit 1312
Brand: Thule Pages: 8

Brands by name

Popular brands

Load more brands