Chrysler 300 SRT8 2010 User Manual Download Page 427 | Manualshive

Page: 427 / 449

background image

DEPARTMENT OF TRANSPORTATION UNIFORM
TIRE QUALITY GRADES

The following tire grading categories were established by
the National Highway Traffic Safety Administration. The
specific grade rating assigned by the tire’s manufacturer
in each category is shown on the sidewall of the tires on
your vehicle.

All passenger car tires must conform to Federal safety
requirements in addition to these grades.

Treadwear

The Treadwear grade is a comparative rating, based on
the wear rate of the tire when tested under controlled
conditions on a specified government test course. For
example, a tire graded 150 would wear one and one-half
times as well on the government course as a tire graded
100. The relative performance of tires depends upon the
actual conditions of their use, however, and may depart

significantly from the norm due to variations in driving
habits, service practices, and differences in road charac-
teristics and climate.

Traction Grades

The Traction grades, from highest to lowest, are AA, A, B,
and C. These grades represent the tire’s ability to stop on
wet pavement, as measured under controlled conditions
on specified government test surfaces of asphalt and
concrete. A tire marked C may have poor traction perfor-
mance.

WARNING!

The traction grade assigned to this tire is based on
straight-ahead braking traction tests, and does not
include acceleration, cornering, hydroplaning, or
peak traction characteristics.

9

IF YOU NEED CONSUMER ASSISTANCE

427

«
...
425
426
427
428
429
...
»

Summary of Contents for 300 SRT8 2010


































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 SRT8 2010

Brand: HALE Pages: 44

Brand: RAM Commercial Pages: 12

Brand: Yakima Pages: 8

Indigo MANZA QUADRAJET 90

Brand: TATA Motors Pages: 10

Brand: Hama Pages: 75

Brand: Metra Electronics Pages: 8

Brand: Ecco Pages: 12

Brand: Oldsmobile Pages: 248

Brand: TATA Motors Pages: 308

Civic Hatch 2017

Brand: Honda Pages: 687

Brand: Yakima Pages: 10

Brand: ULTIMATE SPEED Pages: 56

Brand: Erich Jaeger Pages: 16

Brand: Kargo Master Pages: 10

Brand: Proxel Pages: 16

Brand: Boyo Pages: 2

Brand: Valeo Pages: 76

IREESE TACTICAL 70894

Brand: Horizon Global Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands