Chrysler 300 SRT8 2010 User Manual Download Page 17 | Manualshive

Page: 17 / 449

background image

CAUTION!

•

Always remove the Key Fobs from the vehicle and
lock all doors when leaving the vehicle unat-
tended.

•

For vehicles equipped with Keyless Go, always
remember to place the ignition in OFF.

At the time of purchase, the original owner is provided
with a four-digit Personal Identification Number (PIN).
Keep the PIN in a secure location. This number is
required for authorized dealer replacement of Key Fobs.
Duplication of Key Fobs may be performed at an autho-
rized dealer, this procedure consists of programming a
blank Key Fob to the vehicle electronics. A blank Key Fob
is one that has never been programmed.

NOTE:

When having the Sentry Key

威

Immobilizer

System serviced, bring all vehicle Key Fobs with you to
the authorized dealer.

Customer Key Programming

Programming of Key Fobs and their RKE transmitters
may be performed at an authorized dealer.

General Information

The Sentry Key

威

system complies with FCC rules Part 15

and with RSS-210 of Industry Canada. Operation is
subject to the following conditions:

•

This device may not cause harmful interference.

•

This device must accept any interference that may be
received, including interference that may cause undes-
ired operation.

VEHICLE SECURITY ALARM — IF EQUIPPED

The Vehicle Security Alarm monitors the vehicle doors
for unauthorized entry and the ignition switch (and
Keyless Go Start/Stop button) for unauthorized opera-
tion. If something triggers the alarm, the Vehicle Security
Alarm will prevent the vehicle from starting and provide

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

17

«
...
15
16
17
18
19
...
»

Summary of Contents for 300 SRT8 2010


































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 SRT8 2010

Brand: cam Pages: 2

Brand: Dapper Lighting Pages: 2

Brand: Zavoli Pages: 26

Brand: Dynojet Pages: 68

Brand: Kuda-Phonebase Pages: 3

Brand: Yakima Pages: 21

Brand: muth Pages: 10

Brand: Fab Fours Pages: 13

Brand: Subaru Pages: 2

Brand: Subaru Pages: 328

Brand: Ecco Pages: 24

RVS systems RVS-M641

Brand: Safe Fleet Pages: 24

Brand: Whelen Engineering Company Pages: 4

Brand: AA Products Pages: 8

Civic Coupe 2009

Brand: Honda Pages: 414

Brand: Ecco Pages: 11

Brand: AA Products Pages: 6

NANO CONNECT Smartview 72

Brand: NanoCam Plus Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands