Chrysler 300 SRT8 2010 User Manual Download Page 145 | Manualshive

Page: 145 / 449

background image

If you activate the washer while the windshield wiper
control is in the delay range, the wipers will operate for
two wipe cycles after releasing the multifunction lever and
then resume the intermittent interval previously selected.

If you activate the washer while the windshield wiper is
turned off, the wipers will operate for three wipe cycles
and then turn off.

Headlights On with Wipers

When this feature is active, the headlights will turn on
approximately 10 seconds after the wipers are turned on
if the headlight switch is placed in the AUTO position. In
addition, the headlights will turn off when the wipers are
turned off if they were turned on by this feature.

The Headlights On with Wipers feature can be enabled or
disabled. Refer to ”Headlights On with Wipers,” under
“Personal Settings (Customer-Programmable Features)”
under “Electronic Vehicle Information Center (EVIC)” in
Section 4.

Rain Sensing Wipers

This feature senses moisture on the windshield and
automatically activates the wipers for the driver. This
feature is especially useful for road splash or over spray
from the windshield washers of the vehicle ahead. Rotate
the end of the multifunction lever to one of the six
intermittent wiper settings to activate this feature.

The sensitivity of the system is adjustable from the
multifunction lever. Wiper delay position 1 is the least
sensitive and wiper delay position 6 is the most sensitive.
Choose setting 3 or 4 for normal rain conditions. Choose
setting 2 or 1 if you desire less wiper sensitivity. Choose
setting 5 or 6 if you desire more sensitivity. The rain sense
wipers will automatically change between an intermit-
tent wipe, slow wipe and a fast wipe depending on the
amount of moisture that is sensed on the windshield.
Place the multifunction lever in the off position when not
using the system.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

145

«
...
143
144
145
146
147
...
»

Summary of Contents for 300 SRT8 2010


































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 SRT8 2010

Brand: Hama Pages: 2

Brand: Q'STRAINT Pages: 10

Brand: RaceChip Pages: 20

Brand: Trailboss Pages: 5

Brand: Velleman Pages: 6

Brand: Whispbar Pages: 15

Brand: Dodge Pages: 24

Brand: Jeep Pages: 1528

Brand: STO N SHO Pages: 7

Challenger 2013

Brand: Dodge Pages: 543

Brand: FALCON RIDGE Pages: 7

Brand: Volvo Pages: 30

Brand: tams elektronik Pages: 19

Brand: Toyota Pages: 636

Brand: Hyundai Pages: 19

Portable Car Umbrella

Brand: Mynew Pages: 5

Brand: Volvo Pages: 92

Brand: Summit Racing Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands