Chrysler 300 SRT8 2010 User Manual Download Page 360 | Manualshive

Page: 360 / 449

background image

Materials Added to Engine Oil

Do not add any supplemental materials, other than leak
detection dyes, to the engine oil. Engine oil is an engi-
neered product and its performance may be impaired by
supplemental additives.

Disposing of Used Engine Oil and Oil Filters

Care should be taken in disposing of used engine oil and
oil filters from your vehicle. Used oil and oil filters,
indiscriminately discarded, can present a problem to the
environment. Contact your authorized dealer, service sta-
tion, or governmental agency for advice on how and where
used oil and oil filters can be safely discarded in your area.

Engine Oil Filter

The engine oil filter should be replaced at every engine
oil change.

Engine Oil Filter Selection

This manufacturer’s engines have a full-flow type oil
filter. Use a filter of this type for replacement. The quality

of replacement filters varies considerably. Only high
quality filters should be used to assure most efficient
service. MOPAR

威

engine oil filters are a high quality oil

filter and are recommended.

Engine Air Cleaner Filter

Refer to the “Maintenance Schedule” in Section 8 for the
proper maintenance intervals.

WARNING!

The air induction system (air cleaner, hoses, etc) can
provide a measure of protection in the case of engine
backfire. Do not remove the air induction system (air
cleaner, hoses, etc) unless such removal is necessary
for repair or maintenance. Make sure that no one is
near the engine compartment before starting the
vehicle with the air induction system (air cleaner,
hoses, etc) removed. Failure to do so can result in
serious personal injury.

360

MAINTAINING YOUR VEHICLE

«
...
358
359
360
361
362
...
»

Summary of Contents for 300 SRT8 2010


































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 SRT8 2010

Brand: RAM Pages: 292

Brand: RAM Pages: 116

Multiple G9F18 AU000

Brand: Genesis Pages: 3

Brand: Mobis Pages: 16

Brand: Subaru Pages: 216

Brand: Ford Pages: 368

Brand: Cadillac Pages: 368

Brand: Luverne Pages: 3

Brand: Navman Pages: 27

Brand: Hyundai Pages: 280

Brand: Whispbar Pages: 14

Brand: Mercedes-Benz Pages: 358

Brand: Softride Pages: 4

Brand: Ford Pages: 458

Interlock 700 Series

Brand: Scania Pages: 82

Perfect Fit MBM120

Brand: Waeco Pages: 3

Brand: Or-Fab Pages: 4

Brand: PUTCO Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands