Chrysler 300 SRT8 2010 User Manual Download Page 78 | Manualshive

Page: 78 / 449

background image

Exhaust Gas

WARNING!

Exhaust gases can injure or kill. They contain carbon
monoxide (CO), which is colorless and odorless.
Breathing it can make you unconscious and can
eventually poison you. To avoid breathing (CO)
follow these safety tips:

Do not run the engine in a closed garage or in confined
areas any longer than needed to move your vehicle in or
out of the area.

If it is necessary to sit in a parked vehicle with the engine
running, adjust your heating or cooling controls to force
outside air into the vehicle. Set the blower at high speed.

If you are required to drive with the trunk/liftgate open,
make sure that all windows are closed and the climate
control BLOWER switch is set at high speed. DO NOT
use the recirculation mode.

The best protection against carbon monoxide entry into
the vehicle body is a properly maintained engine exhaust
system.

Whenever a change is noticed in the sound of the exhaust
system, when exhaust fumes can be detected inside the
vehicle, or when the underside or rear of the vehicle is
damaged, have a competent mechanic inspect the com-
plete exhaust system and adjacent body areas for broken,
damaged, deteriorated, or mispositioned parts. Open
seams or loose connections could permit exhaust fumes
to seep into the passenger compartment. In addition,
inspect the exhaust system each time the vehicle is raised
for lubrication or oil change. Replace as required.

78

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
76
77
78
79
80
...
»

Summary of Contents for 300 SRT8 2010


































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 SRT8 2010

Brand: Vauxhall Pages: 323

Prestige APS-45B

Brand: Audiovox Pages: 8

Brand: Volvo Pages: 138

Brand: Prorack Pages: 14

Brand: Chariot Carriers Pages: 3

Brand: Motoalliance Pages: 8

Brand: Veigel Pages: 24

Brand: Cellular Line Pages: 25

XEBRA ZAPCAR Series

Brand: Zap Pages: 16

GMC Yukon Denali 2005

Brand: Cadillac Pages: 456

Brand: Saab Pages: 63

Brand: R&G Pages: 20

Brand: Whispbar Pages: 70

Brand: NavInc Pages: 6

Denali 1094-0185-15

Brand: E&G Classics Pages: 3

Brand: Metra Electronics Pages: 2

Brand: Mercedes-Benz Pages: 398

Brand: Xpresskit Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands