Chrysler 300 SRT8 2010 User Manual Download Page 300 | Manualshive

Page: 300 / 449

background image

NOTE:

Under a maximum loaded vehicle condition,

gross axle weight ratings (GAWRs) for the front and rear
axles must not be exceeded. For further information on
GAWRs, vehicle loading, and trailer towing, refer to
“Vehicle Loading” in this section.

To determine the maximum loading conditions of your
vehicle, locate the statement “The combined weight of
occupants and cargo should never exceed XXX lbs or
XXX kg” on the Tire and Loading Information placard.
The combined weight of occupants, cargo/luggage and
trailer tongue weight (if applicable) should never exceed
the weight referenced here.

Steps for Determining Correct Load Limit

1. Locate the statement “The combined weight of occu-
pants and cargo should never exceed XXX lbs or XXX kg”
on your vehicle’s placard.

2. Determine the combined weight of the driver and
passengers that will be riding in your vehicle.

3. Subtract the combined weight of the driver and pas-
sengers from XXX lbs or XXX kg.

4. The resulting figure equals the available amount of
cargo and luggage load capacity. For example, if “XXX”
amount equals 1,400 lbs (635 kg) and there will be five
150 lb (68 kg) passengers in your vehicle, the amount of
available cargo and luggage load capacity is 650 lbs
(295 kg) (since 5 x 150 = 750, and 1400 – 750 = 650 lbs
[295 kg]).

300

STARTING AND OPERATING

«
...
298
299
300
301
302
...
»

Summary of Contents for 300 SRT8 2010


































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 SRT8 2010

Brand: Federal Signal Corporation Pages: 8

Brand: Federal Signal Corporation Pages: 8

Brand: Axxess Pages: 8

Brand: SeaSucker Pages: 9

Brand: Prorack Pages: 14

Brand: Honda Pages: 32

Brand: V8 equipment Pages: 17

Brand: Waeco Pages: 172

Brand: VBG Pages: 16

BTFREQ PRO BTFMPD3SR

Brand: Scosche Pages: 16

Brand: Warn Pages: 5

Sprinter Side Ladder

Brand: FVC Pages: 8

Brand: GARO Pages: 15

Brand: Edelbrock Pages: 2

Brand: Mercedes-Benz Pages: 93

CF-UFORCE-DRW01

Brand: FALCON RIDGE Pages: 6

Brand: Arrista Pages: 2

Brand: Jaeger Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands