Chrysler 300 SRT8 2010 User Manual Download Page 94

Page: 94 / 449

Call by Saying a Name

•

Press the

button to begin.

•

After the

⬙

Ready

⬙

prompt and the following beep, say

“Call.

⬙

•

The system will prompt you to say the name of the
person you want to call.

•

After the

⬙

Ready

⬙

prompt and the following beep, say

the name of the person you want to call. For example,
you can say

⬙

John Doe,

⬙

where John Doe is a previ-

ously stored name entry in the uconnect™ phonebook
or downloaded phonebook. To learn how to store a
name in the phonebook, refer to

⬙

Add Names to Your

uconnect™ Phonebook,

⬙

in the phonebook.

•

The uconnect™ system will confirm the name and
then dial the corresponding phone number, which
may appear in the display of certain radios.

Add Names to Your uconnect™ Phonebook

NOTE:

Adding names to the uconnect™ phonebook is

recommended when the vehicle is not in motion.

•

Press the

button to begin.

•

After the

⬙

Ready

⬙

prompt and the following beep, say

⬙

Phonebook New Entry.

⬙

•

When prompted, say the name of the new entry. Use of
long names helps the voice recognition and it is
recommended. For example, say

⬙

Robert Smith

⬙

Robert

⬙

instead of

⬙

Bob.

⬙

•

When prompted, enter the number designation (e.g.,

⬙

Home,

⬙ ⬙

Work,

⬙ ⬙

Mobile,

⬙

Pager

⬙

). This will allow

you to store multiple numbers for each phonebook
entry, if desired.

•

When prompted, recite the phone number for the
phonebook entry that you are adding.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 300 SRT8 2010


































































































































































































































































































































































































































































Search results

Summary of Contents for 300 SRT8 2010

Reviews:

Related manuals for 300 SRT8 2010

Brands by name

Popular brands

Chrysler 300 SRT8 2010, User Manual

Search results

Summary of Contents for 300 SRT8 2010

Reviews:

Related manuals for 300 SRT8 2010

Brands by name

Popular brands