Chrysler 300 SRT8 2010 User Manual Download Page 278 | Manualshive

Page: 278 / 449

background image

at least one second. The transmission will now operate
automatically, shifting between the five available gears.

General Information

•

You can start out in first or second gear. The system
will ignore attempts to upshift at too low of a vehicle
speed.

•

The transmission will automatically downshift to first
gear when coming to a stop.

•

Starting out in second gear is helpful in snowy or icy
conditions.

•

Avoid using speed control when Autostick

威

is en-

gaged.

•

The transmission will automatically shift up when
maximum engine speed is reached while Autostick

威

is

engaged.

•

Transmission shifting will be more crisp/abrupt when
Autostick

威

is engaged.

DRIVING ON SLIPPERY SURFACES

Acceleration

Rapid acceleration on snow covered, wet, or other slip-
pery surfaces may cause the rear wheels to pull errati-
cally to the right or left. This phenomenon occurs when
there is a difference in the surface traction under the rear
(driving) wheels.

WARNING!

Rapid acceleration on slippery surfaces is dangerous.
Unequal traction can cause sudden pulling of the rear
wheels. You could lose control of the vehicle and
possibly have an accident. Accelerate slowly and
carefully whenever there is likely to be poor traction
(ice, snow, wet mud, loose sand, etc.).

278

STARTING AND OPERATING

«
...
276
277
278
279
280
...
»

Summary of Contents for 300 SRT8 2010


































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 SRT8 2010

Brand: Lancia Pages: 191

Brand: A-Tach Mounts Pages: 2

Brand: Ultra Start Pages: 8

Brand: Carax Pages: 2

Brand: Whispbar Pages: 16

Brand: Trailboss Pages: 5

Brand: Subaru Pages: 21

Brand: Xblitz Pages: 30

Brand: Hella Pages: 21

Brand: Hank Pages: 2

Brand: SCC Pages: 4

Brand: Road Ranger Pages: 22

Brand: Paser Pages: 2

Brand: Xblitz Pages: 56

Brand: BraunAbility Pages: 46

Brand: Lexus Pages: 830

Brand: CARFACE Pages: 16

Brand: SSV Works Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands