Chrysler 300 SRT8 2010 User Manual Download Page 52 | Manualshive

Page: 52 / 449

background image

BeltAlert

威

will be reactivated if the driver’s seat belt is

unbuckled for more than 10 seconds and the vehicle
speed is greater than 5 mph (8 km/h).

BeltAlert

威

Programming

The BeltAlert

威

can be enabled or disabled by your

authorized dealer or by performing the following steps:

NOTE:

Chrysler Group LLC does not recommend de-

activating the BeltAlert

威

.

1. With all doors closed, and the ignition switch in any
position except RUN or START, buckle the driver’s seat
belt.

2. Turn the ignition switch to the RUN position, but do
not start the engine. Wait for the Seat Belt Reminder Light
to turn off and then proceed to the next step.

NOTE:

You must perform the following steps within

60 seconds of turning the ignition switch to the RUN
position.

3. Within 60 seconds of turning the ignition switch to the
RUN position, unbuckle and then re-buckle the driver’s
seat belt at least three times within 10 seconds, ending
with the seat belt buckled.

NOTE:

Watch for the Seat Belt Reminder Light to turn

on while unbuckling the seat belt and turn off while
re-buckling the seat belt. It may be necessary to retract
the seat belt.

4. Turn the ignition switch to the OFF position. A single
chime will sound to signify that you have successfully
completed the programming.

BeltAlert

威

can be reactivated by repeating this procedure.

52

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
50
51
52
53
54
...
»

Summary of Contents for 300 SRT8 2010


































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 SRT8 2010

Brand: Daihatsu Pages: 485

Porsche 911 Turbo S Wheel

Brand: FANATEC Pages: 9

Brand: RAM Pages: 292

Brand: RAM Pages: 116

Brand: Yakima Pages: 8

Brand: Yakima Pages: 8

Brand: Ford Pages: 2

Brand: RAM Pages: 76

Brand: Advantech Pages: 59

Brand: Fiat Pages: 24

Brand: Valeo Pages: 28

Brand: Westin Pages: 2

Brand: Thule Pages: 12

Brand: Camoplast Pages: 19

2011 SRX CROSSOVER

Brand: Cadillac Pages: 416

Brand: TIE DOWN Pages: 2

Brand: Audi Pages: 63

MultiCharger 1204

Brand: DEFA Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands